what is the unit of the medium resistance and the specific cake resistance Data:Ws = 393g = 0.393 kg%3DP1 = 0.3 kg/cm²Po = 0.1 kg/cm²V1 = 10 LArea of filtrate tank (A) = 0.0398 m2%3DViscosity of the filtrate (u) = 9.03 ×10-5 N-sec/m2Density of white ceramic (p,) = 1600 kg/m3Vol = A xh= 0.0398 x 0.04 = 1.592 x 10-3 m³ДР — Р — Р.= 0.3 – 0.1 = 0.2 kg/cm2 = 2000kg/m²1804500%3DV/A0.04slope = m = 98193intercept = c = 649.78 To find the specific cake resistance (a):uxaxWsslopeΔΡΧ2χρs9.03 х10-5хах0.393= 981932000x2x160098193 x 2000x2x1600a =1.77 x 10169.03 x10-5 x 0.393To find the medium resistance (Lm):μχα= interceptAPx Lm9.03 x10-3x1.77×1016= 649.782000x Lm9.03 x10-5x1.77x1016Lm= 1.22 x 1062000x649.78

Given Resistance To find Unit of Cake resistance Unit of Medium resistance

Answered: what is the unit of the medium…

Engineering

Mechanical Engineering

what is the unit of the medium resistance and the specific cake resistance

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sintered silicon nitride parts are expected to experience tensile stresses 50% of the ultimate tensile strength of the material. What will be the maximum allowable size of internal flaws for these parts not to fail in service? Given the following properties of the material: Specific surface energy: 0.3 J/m2 its Youngs Modulus: 304 GPa Ultimate tensile Strength: 570 MPa Select one: a. 1.43 µm b. 0.71 µm c. 15 µm d. 85 µm e. 9.5 µm
Comparing the thermal barrier coatings (TBCs) with the superalloy components of high performance aerospace turbine blades, which of the following statements are true? Select one or more: O a. The ductility of the TBCs is lower than the superalloys O b. The ductility of the superalloys is lower than the TBCs O c. The TBCs have the same thermal conductivity as the superalloys Od. The superalloys have higher thermal conductivity than the TBCs. O e. The thermal expansion of the TBCs is lower than that of the superalloys
...2/ A plant wishes to dry a certain type of fiberboard. To determine drying characteristic, a sample of 0.3 × 0.3 m with edges sealed was suspended from a balance and exposed to a current of hot dry air. Initial moisture content was 75%. The sheet lost weight at the rate of 1 104 Kg /s unit the moisture content fell to 60%. It was established that the equilibrium moisture content was 10 %.The dry mass of the sample was 0.90 Kg.All moisture contents were on wet basis .Determine the time for drying the sheets from 75% to 20% moisture under the same drying conditions.
Comparing the thermal barrier coatings (TBCs) with the superalloy components of high performance aerospace turbine blades, which of the following statements are true? Select one or more: a. The TBCs have the same thermal conductivity as the superalloys b. The ductility of the TBCs is lower than the superalloys □c. The ductility of the superalloys is lower than the TBCs d. The superalloys have higher thermal conductivity than the TBCs. The thermal expansion of the TBCs is lower than that of the superalloys e.
A siilicon boule has been processed through grinding to provide a cylinder whose diameter = 281 mm and whose length = 899 mm. Next, it will be sliced into wafers 0.8 mm thick using a cut-off saw with a kerf = 0.5 mm. The wafer thus produced will be used to fabricate as many IC chips as possible for the personal computer market. Each IC has a market value to the company of $108. Each chip is square with 17 mm on a side. The processable area of each wafer is defined by a diameter = 265 mm. Estimate the value of all of the IC chips that could be produced (in $), asssuming an overall yield of 84% good product.
Write one to two paragraph Executive Summary of a shell and tube heat exchange and the manufacturing process. ( USE YOUR OWN WORDS DONT COPY)
118 ABOUT INDUSTRIAL PIPING IN WHAT SITUATION IS IT NECESSARY TO PERFORM FLEXIBILITY CALCULATION IN PIPING SYSTEMS
Pick the best soultion for the multiple choices. Modulus of resilience is: Slope of elastic portion of stress – strain curve Area under the elastic portion of the stress –strain curve Energy absorbed during fracture in a tension test Energy absorbed during fracture in an impact test Slope of the plastic portion of the stress- strain curve ( ) Fatigue failure occurs under the condition of: High elastic stress High corrosivity High stress fluctuations High temperature High rate of loading ( ) Creep failure of a material occurs most rapidly when the operating temperature is: Cryogenic temperature Equal to its melting point Grater than 0.4 times its melting point in K Greater than 200 oF Close to boiling point ( ) Young’s modulus of a material is indicative of its: Tensile strength Yield Strength Ductility Stiffness Corrosion Resistance…
In a thin-walled cylindrical pressure vessel, the axial and circumferential joint efficiencies specified to account for fabrication process and inspection procedure considerations are 1.0 and 0.5 respectively. The ratio between the circumferential stress and axial stress used in the design is, O a. 4:1 O b. 1:1 Oc. 2:1 O d. 1:2
020 ABOUT INDUSTRIAL PIPING WHAT ARE THE POSSIBLE TRANSIENT OPERATING CONDITIONS FOR PIPING SYSTEMS?
Normally when the creep is considered in materials?
What exactly is involved in the length property?