What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 289 mm and an over-all depth of 494 mm? The specified compressive lightweight concrete is 25.8 MPa and the yield strength of stirrups is 289 MPa. The distance of tension reinforcements from the outer fiber of the beam is 54 mm. Round off your final answer in 3 decimal places. Loadings:

What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 289 mm and an over-all depth of 494 mm? The specified compressive lightweight concrete is 25.8 MPa and the yield strength of stirrups is 289 MPa. The distance of tension reinforcements from the outer fiber of the beam is 54 mm. Round off your final answer in 3 decimal places. Loadings:

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
i need the answer quickly
The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table. Determine: a. The maximum force P that can be applied at C. Answ: 84.22 kN. b. The deformation at the point where the load is applied. Answ: 1.5278 mm.
hi there, can you help me answer this question please? thank you.
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
Calculate the steel ratio that will produce a tension-controlled failure if compressivestrength f’c = 28 MPa and steel yield strength fy the answer is 0.02167 but i don't know how to solve it please help
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
I need the answer quickly