What is the RPI index? How can the defective product rate of a production process be determined by using the RPI index? The average distribution range of 2 samples consisting of 4 units is R = 10.8 mm. The tolerance limit is plus – minus 10 mm. Calculate the RPI and evaluate if it will reject. What happens to the reject situation if the tolerance limit is plus-minus 20 mm?

What is the RPI index? How can the defective product rate of a production process be determined by using the RPI index? The average distribution range of 2 samples consisting of 4 units is R = 10.8 mm. The tolerance limit is plus – minus 10 mm. Calculate the RPI and evaluate if it will reject. What happens to the reject situation if the tolerance limit is plus-minus 20 mm?

A First Course in Probability (10th Edition)

10th Edition

ISBN:9780134753119

Author:Sheldon Ross

Publisher:Sheldon Ross

Chapter1: Combinatorial Analysis

Section: Chapter Questions

Problem 1.1P: a. How many different 7-place license plates are possible if the first 2 places are for letters and...

See similar textbooks

Similar questions

Calculate the annual arithmetic mean, geometric mean, and percentage exceedance (>400 col/100ml) for Fecal Coliforms for the year? What does the difference in the arithmetic and geometric means tell us about the data? What is the total load (in both kg and lbs) of Nitrogen and Phosphorous for the year?
1 40. Below is another figure from the same paper, showing the effect of the studied GOS on wrinkle area, percent of wrinkles, number of wrinkles and wrinkle depth. Please consult the figure and answer the related questions below: Total wrinkle area (mm²) Wrinkle depth (um) 1000 500 0 -500 -1000 -1500 p<0.05 Control group p<0.05 Percent of wrinkle area (%) 4 -21 100 50 -50 -100 Control group GOS group GOS group Figure 3. Effects of galacto-oligosaccharides (GOS) on wrinkle formation in healthy adults. The p values indicate a significant difference between changes in the two groups at each week by r test. All data were two-sided at the 5% significance level and are reported as means standard error of the mean. Number of wrinkles -150 A. Is there a significant effect of GOS on any of the parameters shown in the figure? If so, which ones? B. The authors state in the paper that "the wrinkle depth and the number of wrinkles in the GOS group were lower than that in the control group although…
A process has a process capability ratio, C, =1.38, At some time the process seems to have a mean shifted left of the center. The process capability index,Cpk, is found to be 0.78, and the mean is left-shifted, that is the current mean is mess than the mean of the control chart. Determine the Z (UTL) with respect to the current left-shifted mean.
What is formula for t RATIO FOR A SINGLE POPULATION MEAN?
The failure time of a certain component has a Weibull distribution with B = 4, 0 = 2000, and y = 1000.Determine the reliability of the component and the hazard rate for an operating times of 1400 and 1800 hours respectively.
zions Management Spring21 Time left 1:09:43 In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 4 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 156.46, 199.62, 189.31, 102.22, and112.09 respectively. In the same sample, the corresponding ranges are: 11.97, 12.17, 13.94, 11.86, and 11.83 respectively. What are the lower and upper control limits for the R chart? O a. 0,31.17 O b. 0,28.17 O c. 0,29.17 O d. None is correct O e. 0,24.71 O f. 0,30.47. NEXT PAGE a Type here to search
The table below shows the results from the specific gravity (S.G.) test performed in a soil laboratory including twenty samples of sand. Construct "less than" cumulative frequency distribution and "Ogive". Determine the number of samples have S.G. less than 2.65.
ANSWER 1-3
kindly help me with this exercise thank you! Answer only 1and 2
How to find the relative and percent error in this data?
Please see below. Note that I am only given one attempt at this and I believe that the answer I have may not be correct. In selecting the sample size to estimate the population proportion pp, if we have no knowledge of even the approximate value of the sample proportion p̂ p^, we:A. take two more samples and find the average of their p̂ p^B. let p̂ =0.95p^=0.95C. let p̂ =0.50p^=0.50D. take another sample and estimate p̂ p^ Under which of the following circumstances is it impossible to construct a confidence interval for the population mean?A. A normal population with a large sample and a known population variance.B. A normal population with a small sample and an unknown population variance.C. A non-normal population with a large sample and an unknown population variance.D. A non-normal population with a small sample and an unknown population variance.
Type size Mean S.D. I 10 136.7 4.5 II 15 138.3 4.6 7. | find the 98% econfidence interval for the difference of mean fabric strengths for the two types using a pooled interval. Interpret your answer.