What is the net effective area for the angle section as shown in figure? The angles are connected with M18 bolts of grade 4.6. 40 60 ISA 100 x 75 x 10 mm 18 mm diameter staggered bolt at 55 mm pitch 45 mm 30 mm 101

What is the net effective area for the angle section as shown in figure? The angles are connected with M18 bolts of grade 4.6. 40 60 ISA 100 x 75 x 10 mm 18 mm diameter staggered bolt at 55 mm pitch 45 mm 30 mm 101

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: SITUATION 1 The tension member shown in the figure contains holes for 1-in Ø bolts. At what spacing,…

Q: 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy-36ksi, Fu=58ksi…

A: Given Data: A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole…

Q: The plate shown is 8 in wide and 1/2 in thick. The bolts are 7/8 in. The smallest net area (An) of…

A: Given:- width of plate =8 inthickness of plate =1/2 inBolts diameter size = 7/8 inA36 plateTo…

Q: The angle shown below is A992 steel joined to a 3/4 in thick gusset plate (not shown) with 3 bolts.…

A: Consider the given data The bolts are group A bolts with thread not excluded from the shear plane,…

Q: WT12×153 05 WT12×153 Determine the design strength of two WT-shapes (WT12×153) connected by plates…

A: We have to determine the design strength of two WT-shapes (WT12x153) connected by plates with 1 in…

Q: Situation 9: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (22mm dia) cut into the plate…

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

Q: lines of M20 bolts shown in the figure, determine the pitch (s) in mm that will give it a net area…

Q: ¿A Tension member has used to resist load of 65 kips, and the shear stress on bolts is 15.9 kips.…

A: If two or more plates are to be joined then the bolts or welding is used. The applied shear stress…

Q: A staggered bolted connection has bolts arranged as shown. Diameter of bolts is 19 mm. Fy = 248 MPa.…

Q: The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will…

Q: discuss the possible failure modes when in different bolts when the bolts are subjected to shear,…

A: Possible Failure Modes of Bolts in Shear, Tension, and Combined LoadingBolts are critical components…

Q: An angle section ISA 120 x 100 x 10 is shown in the figure. The bolts used are of diameter 20 mm.…

A: Given data, For ISA 120x100x10 Diameter=20 mm Steel grade is Fe410

Q: Find the ava shown in the liameter bolts Use LRFI Use ASD 1 2) 3½" I

Q: As shown in the figure below, a C7 x 12.25 tension member of A572 Gr 50 steel is connected to the…

A: Answer We know that allowable strength of a member is given by minimum of the following strength 1)…

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: olt (threads are not excluded from shear planes) that could resist the loads without failing. Assume…

Q: a. Prepare a table showing values of Group A bolt shear strength and slip-critical strength for…

A: Shear strength: The maximum load that can be resisted by the structure is known as shear strength.…

Q: Calculate the critical net area (mm²) for the tension member shown. The bolts are M22. 40 65 90 115…

A: Given A tension member Required Net area

Q: What is the required bolt diameter at B in mm? * 8.94 10.45 6.32 5.22 13.66 Compute the reaction at…

Q: What is the nominal maximum load capacity of grade 60 reinforcing bar with a diamter of 20mm?…

Q: The block shear strength of the tension member as shown in figure is (round off to two decimal…

A: For given tension member,grade of plate Fe410Angle specification: -ISA 80 x 50x 8 mmBolt…

Q: A 620×230 UB 125 tension member of S355 steel is connected through both flanges by 30 mm bolts (in…

A: Properties of 620x230 UB 125 w = Weight of beam = 125 kgD = Total depth of beam = 620 mmbf = Width…

Q: Find ØR, considering bolt limit states only. (S275 Steel, fy = 2804 kgf/cm², fu = 4385 kgf/cm²,…

A: fy = 2804kgf/cm2 = 2804 * 9.81/100 N/mm2 = 275N/mm2 fu = 4385kgf/cm2 = 4385 * 9.81/100 N/mm2 =…

Q: Determine the design strength (LRFD)

A: Solution: calculate the strength of the plates as tension members Gross area Ag = 10(0.5) = 5 sq in…

Q: Problem 2: For the Channel as shown in the figure below determine the design and allowable strength.…

A: We have to determine the value of design and allowable strength. The holes are for 18 mm diameter…

Q: a. Determine the ultimate tensile strength of the tension member (channel) based on its gross area.…

A: For channel fu = 450MPa fy = 345MPa

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: Determine the strength of the connection shown in Figure , based on bearing and shear, for the…

A: For both holes, calculating the bearing deformation strength:Rn=2.4dtFu =2.4(3/4)(3/8)(58) =39.15…

Q: In the connection shown in the figure, the bolts are 3/4 inch in diameter, and A50 steel is used for…

A: The given data is shown below: Diameter of bolt=34-inchA50 steel

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: Situation 16. The L150x100x12mm, A36 Steel (Fy = 248 MPa, Fu = 400 MPa) shown in the figure has one…

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard…

A: Given- diameter of bolts=20mmFu=370MpaFy=240MpaFor UNP 300B=100mtf=16mmAN=0.949m2/m

Q: An A36 (Fy=248MPA, Fu=400MPA) steel plate with thickness, t=llmm used as a tension member is…

Q: Determine the tensile capacity of a 200 x 100 x 12 mm angle in S275 steel assuming that the angle is…

A: 200 x 100 x 12 mm angle S275 steelM24 bolts (3 bolts in a row and p = 70 mm)

Q: A 300 x 12 mm plate is connected to 23mm diameter bolts arranged as shown, what is the capacity P =…

A: Answer We are given Plate b =300 mm and t = 12 mm bolt diameter d = 23 mm allowable stress for…

Q: 1. Two A36 16mm thick steel plates are connected by four rivets shown. 50 PU O 50 x 50 50 a.…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: 1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and…

A: The formula to calculate the direct shear is given by, F1=Fn ...1 Here, F is given…

Q: GOmm 5omm 10omM 100mm 100mm EOmm 150mm

A: Diamter of bolt (d) = 33 mm Let's 2mm extra is provide in hole So diameter of hole (dh) = 33+2 =…

Q: Grade: 10.9 Included I Grade: S235 ace Class: C atio of the mean installed bolt pretension to the…

Concept explainers

Volumes

Volume usually is the dimensional quantity that involves the evaluation of any three-dimensional figure enfolded inside a closed space. The SI unit (International System of Units) of volume is m3 and the dimensional unit of volume is [L3]. For estimation of the volume of any figure, various formulae are used. Another application of volume includes the reference in the sound levels, the higher the sound intensity, the louder the sound heard, and hence, the larger the volume. The SI unit of sound volume is decibels (dB).

Question

What is the net effective area for the angle section as shown in figure? The angles are
connected with M18 bolts of grade 4.6.
40
60
ISA 100 x 75 x 10 mm
18 mm diameter
staggered bolt at
55 mm pitch
45 mm
30 mm
10 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Bolting arrangement

VIEW

Step 3: Area calculation

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the effective net area of the tension member shown in the figure. 000 3"3" L6 X 6 X 1/2 %-in. bolts Ciri2 ENGINEERING Section STEEL DESIGN 1.67"
For the bolted tension member is shown in the figure. Determine the effective area, Ae. Given, x = 1.68 inch, Ag = 5.75 inch?. (4)- S/8" A325N bolts L6 x 6 x 1/2 -Tu 3" 3" 3"
1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads excluded from the shear plane and the plates are made of A36 steel. 12 in. xin. 100 12 in. a) Determine the bolt shear strength b) Determine the bearing strength of the plate c) Determine the tensile strength (both gross and net) of the plate d) What is the strength of the bolted connection?
1. answer basing with the new NSCP 2015 guideline codes
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
Which of the following gives the minimum number bolts that can be accommodated in one row of a 350mm flat plate. O 4 O 5 O 6 O 7
Determine the design strength of an UNP200 with four lines if 16 mm diameter bolts in standard holes, as shown in the Figure below. F = 370MPA F. = 240MPa 60 80 60 100, 100, 100, 100,100 UNP 200
3. The figure shows a steel bracket bolted to the face of a steel column. Find the bolt size required for a maximum load (F) = 15 kN. Bolts are to be grade 8.8 and reusable. Assume a coefficient of friction of joint of 0.6. Top View Side View 20 1.57 20 50 70 140 co A Kolo 260 Z DX T130 130 YA |E=15KN Ans: M12
a] Compute LRFD 6.) Compute ASD CIVIL STEEL DESIGN ENGINEERING- BOLTED CONNECTION Sample Problem 5: The 175 x 100 x 16 mm angle shown connected to a gusset plate with three 25 mm bolts (A490) when threads are excluded from shear planes. The angle consists of A36 steel. Properties of 4 175 x 100 x 16 A36 Steel Properties of A490 bolts A = 4181 mm² t = 16 mm Fy = 248 MPa F₁ = 400 MPa Fy = 276 MPa Nominal hole dia. = 27 mm 75 T+ 100 Gusset Plate 100 F 100
The block shear strength of the tension member as shown in figure is (round off to two decimal places). Assume grade of plate Fe410. 45 mm 35 mm 50 mm 100 mm ISA 80 x 50 x 8 mm (M20 bolt of grade 4.6 is used) KN
For the following plate calculate the net section failure resistance. Assume plate thickness as 13mm and Fy=300MPa and Fu=440MPa. (Dimensions in mm) Bolts: M20- Punched 1- 300 13mm Plate 65 -+ 65 100 70 Q² 55-45-