For the following plate calculate the net section failure resistance. Assume plate thickness as 13mm and Fy=300MPa and Fu=440MPa. (Dimensions in mm) Bolts: M20-Punched 300 13mm Plate ·3+3 65 65 100 70 55-45

For the following plate calculate the net section failure resistance. Assume plate thickness as 13mm and Fy=300MPa and Fu=440MPa. (Dimensions in mm) Bolts: M20-Punched 300 13mm Plate ·3+3 65 65 100 70 55-45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts t=12 mm t=12 mm P. P- P 300 75 75 75 Edge distances -75 mm dhole for tensile and rupture d, +3 mm dnole for bearing strength for L- de +1.5 mm Fy 248 MPa F.- 400 MPa
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
Bolted and Riveted Connections From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm bigger than the bolt, the angular section is 100 x 75 x 8 mm, with an area of 1340 mm2. Thickness of the gusset plate is 9mm. The gusset plate and angle arc A36 steel with Fy = 250 MPa and Fu = 400 MPa. Determine the tensile capacity of the connection based on gross area. Determine the tensile capacity of the connection based on effective net area using a reduction factor of 0.85. Determine the tensile capacity of the connection based on gross area.
Need right complete solution
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
Please answer as soon as possible
The diagonal at the left to the connection is a double angle 90 mm x 90 mm x 8 mm, with area of 2700 mm?, bolted to the 8 mm thick gusset plate. Bolt diameter = 16 mm Bolt hole diameter = 18 mm Bolt bearing capacity, Fp = 480 MPa Bolt shear strength, Fv = 68 MPa Steel plate strength and stresses are as follows: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 0.60 Fy Allowable tensile stress on the net area = %3D 0.50 Fu Allowable shear stress on the net area = 0.30 Fu Bolt bearing capacity, Fp = 1.2 Fy Calculate the allowable tensile load, P(kN) under the following conditions: %3D
Please provide the whole (not shortcut) and correct solution with figures. thank you Given: x =175mm Rivet Dia.,=20mm y=200mm Fy=248Mpa Fu=400 Mpa Bolt Dia.=22mm
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
B2 USING NEW NSCP CODES, PLEASE ANSWER
Solve( b) part only in 2 hour plz solve this perfectly this id mecahnical emgeering question so plz don't reject it.