What is the MMC of the ø68 mm boss? and what is the position tolerance on the boss referenced at MMC, LMC, or RFS? 2. How much position tolerance is allowed on the boss if it is produced at a size of 68.1 mm? And what is the MMC of the 3 holes?

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: Find the toggle and limit positions.

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: FIND THE CUBIC SPLINE G(x) for the given data k0 and kn as given 12. fo=f(0) = 1, ₁ = f(2)=9,…

A:

Q: In the belt drive system shown below, the input pulley is attached to an electric motor transferring…

A:

Q: What is the definition of temperature?

A: Given question: What is the definition of temperature?     Given question is related to…

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: What is the measurement accuracy AND unity of the instrument in Figure

A: Accuracy of the Bourdon tube pressure gauge

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: 1-WHICH IS THE SENSOR? 2-WHICH IS THE 3-WHAT IS IT USED FOR? TRANSDUECER?

A: To find-: (a) The sensor in the given figure. (b) The transducer in the given figure. (c) The use of…

Q: Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly…

A:

Q: Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible…

A: Given : To find : Datum features , tolerances

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: Sketch a setup and measurement method that may be used to check the runout tolerance. Also show the…

A: To sketch a setup and measurement method to check runout tolerance. and to show acceptable max…

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.

A: The print sheet is showing the 3D view or perspective of the lower support cylinder union part.

Q: Which statement is true in the case of the term "Range". O Is closely related to accuracy and define…

A: Range is closely related to accuracy

Q: Perform position analysis on the crank slider shown below by 1) labeling the unknown values on the…

A:

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: plete the hole specification including a position tolerance of C ary datum feature A, secondary…

A: Given-Information:- To-Determine:- Complete hole specification

Q: What is the reading on this caliper? Please see attached image.

A: Given  dial calipers Dimension to be measured =Blade scale reading + dial scale reading  We see that…

Q: L. 4 (in circle) 5 (in circle) 6 (in circle) 7 (in circle) 8 (in circle) 1(not in circle) 4(not in…

A: to match the following numbers with correct terminology1 (in circle): 2 (in circle):3 (in circle):4…