7. What are the two hydraulic principles used when determining flow rate using Venturimeters?8. Write the basic discharge equation for a standard, uncontracted, horizontal sharp-crestedweir and define each term.

A venturi meter is a discharge measuring instrument in a pipe flow. It is fitted in a pipe and has a…

What are the two hydraulic principles used when determining flow rate using Venturi meters? Write the basic discharge equation for a standard, uncontracted, horizontal sharp-crested weir and define each term.

What are the two hydraulic principles used when determining flow rate using Venturi meters? Write the basic discharge equation for a standard, uncontracted, horizontal sharp-crested weir and define each term.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The head lost in 150 ml of 0.3 m pipe having sand- grain roughness projections 2.5 mm high is 12 m…

A: Given :

Q: Explain the concept of backwater effect in open channel hydraulics.

A: The backwater effect is an open channel hydraulics phenomenon whereby the water flow upstream of any…

Q: 5. Discuss the difference between the field capacity and the infiltration capacity.

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Determine the characteristics of a unit composed of 2 desilting channels treating a peak wastewater…

A: step 1-

Q: Q3) Determine the depth and width at average and minimum flow and dimensions the weir plate of…

Q: A production well was discharged and tested through an atmospheric silencer at sea level (1 bar…

A: (1)

Q: Describe how the hydraulic grade line is determined for: a. open channel flow and b. at the outlet…

A: Hydraulic grade line represents the sum of pressure head and datum head. So value of HGL changes…

Q: Compute the velocity of the flow for a very smooth pipe if the hydraulic radius is 10ft, and slope…

A: we have hazen williams equation:V=1.318CR0.63S0.54so,C=coefficient ; for smooth pipe…

Q: Calculate the value of the hydraulic radius for flow in an open channel where the bottom of the…

A: Figure of the channel according to given statement:

Q: A storm water discharge of 1.5 m/s flows along a reinforced concrete box culvert with n = 0.015 and…

Q: 10. The hydraulic radius of a circular channel section is 0.33m, calculate the radius of the channel…

Q: WHAT WILL BE THE DISCHARGED OF A RECTANGULAR WEIR IF THE HEIGHT IS 0.4m and LENGTH IS 200m…

A: Introduction : Discharge : A discharge is a measurement of how much fluid flows in a certain amount…

Q: c. Discuss how the hydraulic design of the Overflow weir, Morning glory spillway and Siphon spillway…

Q: AR²/351/2 Derive Manning's equation for turbulent and uniform flow: Q = where Q is " n in m³/s; A,…

Q: Design a circular radial-flow sedimentation tank for a town with a projected population of 45,000.…

A: Populations= 45000 Waste water flow rate = 400 L/capita-d or 0.4 m3/capita-d Detention time (t) = 2…

Q: How can I calculate the water level in a grit chamber at average flow and at peak hourly flow. The…

A: Average daily flow rate, Width of tank, Length, Depth, Elevation, To find: Water level in a grit…

Q: A pipe culvert 45 ft long extends between two reservoirs as shown below. The difference in the water…

Q: A weir in a horizontal channel is 12 ft wide and 4 ft high. The upstream water depth is 5.2 ft.…

A: Width of the weir = 12ft Height = 4ft upstream water depth = 5.2 ft Elevation of the water surface…

Q: The hydraulic radius (m)

A: Given: Diameter of circular pipe=D To find: Hydraulic radius (m)

Q: 6m, calculate the hydraulic depth of the channel.

A: To find : Hydraulic depth.

Q: 5. The ratio between hydraulic radius and hydraulic depth of a triangular channel is 31/100,…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Design a wastewater treatment primary clarifier for an average flow rate of 1.10 MGD, and a peak…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A canal at triangular cross section with discharge 0.3 cumecs, if the depth of water 0.15m, the side…

Q: Question- A circular sewer of dia 1 m carries storm water to a depth of 0.75 m. Find the hydraulic…

A: Given data- Diameter of circular sewer D = 1 m. depth of flow = 0.75 m. To Find- The hydraulic…

Q: You are designing a circular concrete pipe and compute the value of Which of the following…

A: 1. Given data, QAD0.5=3.1 According to FHWA hydraulic design of highway culvert, for QAD0.5≤3.5…

Q: Water at 15°C is pumped from a reservior at a rate of 0.1131 m3/s where the local atmospheric…

A: Vapour pressure at 15oC is 1.7046kPa NPSH=7.8 To find maximum height (hs) before cavitation occur

Q: You have designed a 16-in diameter stormwater pipe to flow at a velocity of 5 ft/s when full. The…

A: Solution: Given Data: Diameter of pipe (D) =16 inch=1.33 ft Velocity of Flow=5 ft/sec Manning's…

Q: . The ratio between hydraulic radiu ydraulic depth of a triangular char 1/100, calculate the side…

Q: How can I calculate the water level in a grit chamber at average flow and at peak hourly flow. The…

A: Average Daily Flow Rate = 2.6 MGD (Million Gallons Per Day)Weir Crest Elevation = 136.00 ft above…

Q: Calculate the discharge for a flow depth of 0.85 m in a trapezoidal open channel with bottom width 1…

A: Givven data:

Q: . Hydraulic properties determined 2. Analysis (Curve matching) 3. Types of pumping tests 4.…

A: Hydraulic properties detemined are - 1. Transmitivity 2. Hydraulic conductivity 3. Storativity…

Q: A water treatment plant has an average influent flow rate of 15 MGD and peak flow rate of 25 MGD…

Q: A 5.7 m diameter circular concrete culvert has a drainage water flowing at a height of 1.3 m.…

Q: Describe, with the aid of a diagram, the development of the flowfield at the start of a pipe and…

Q: ngure (a) What are the boundaries to this flow field? Label each of the four boundaries, noting the…

A: Uplift pressure is also called hydrostatic uplift and in general, is an upward pressure applied to a…

Q: A) A fully penetrating unconfined well of 12 in. The diameter is pumped at a rate of 1 ft^3/sec. The…

A: As per company policy we can only answer first question. Kindly post other questions as seperate…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

7. What are the two hydraulic principles used when determining flow rate using Venturi
meters?
8. Write the basic discharge equation for a standard, uncontracted, horizontal sharp-crested
weir and define each term.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please complete solution.
A production well was discharged and tested through an atmospheric silencer at sea level (1 bar absolute) using a lip pipe with a diameter of 24.5 cm and a weir box with a 90 ° V-notch weir. The well was flowing at a wellhead pressure of 7 bar gauge and the measured lip pipe pressure and weir height were 3 bar gauge and 0.11 m, respectively. Calculate the discharge enthalpy and total mass flow of the well.
I need the answer as soon as possible
Pls answer asap. What is the maximum discharge of a semi-hexagonal shape having a channel bed width of 3 m flowing at a depth of 1.2 m and with a velocity 4.0 m/s ? Write your answer to the nearest whole number.
I need the answer as soon as possible
4-38
A 5.5 m diameter circular concrete culvert has a drainage water flowing at a height of 4.6 m. Compute for the hydraulic radius (in m). Answer in TWO(2) decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
match the items
4. Explain a stagnation pressure. 5. Write the equation to find velocity using a pitot tube and define each term. 6. What is the simplest and more reliable method to measure flow in a pipe? 7. What are the two hydraulic principles used when determining flow rate using Venturi meters? 8. Write the basic discharge equation for a standard, uncontracted, horizontal sharp-crested weir and define each term.
How can I calculate the water level in a grit chamber at average flow and at peak hourly flow. The effluent from the tank flows over a fiberglass, sharp-crested weir that is set at elevation 136.00 ft above sea level (ASL). The average daily flow rate is 2.6 MGD. Assume that all flow must pass through one grit chamber. The dimensions of the grit chamber are 9 ft wide, 30 ft long, and 10.5 ft deep (water depth). The weir extends across the full width of the chamber and find the hydraulic retention time of the grit chamber. HRT at average flow = ______ minutesand HRT at peak hourly flow = ______ minutes
Choose the letter of the correct answer. Please answer honestly and do not just guess. Develop a formula for the discharge over a 90° V-notch weir in terms of head above the bottom of the V. A channel conveys 300 litres/sec of water. At the outlet end there is a 90° V-notch weir for which the coefficient of discharge is 0.58. At what distance above the bottom of the channel should the weir be placed in order to make the depth in the channel 1.30m? a. 0.759 m c. 0.769 m b. 0.749 m d. None of the above From above question, with the weir in this position what is the depth of water in the Cchannel when the flow is 200 litres/sec? a. 1.218 m b. 1.212 m c. 1.232 m d. None of the above It is desired to use the 32 in. pump at 1170 rpm to pump water at 60°C from one reservoir to another 120 ft higher through 1500 ft of 16 in. ID pipe with f = 0.030. Determine the Q. a. 15,000 gpm c. 16,000 gpm 3 b. 15,500 gpm d. None of the above
Design a trapezoidal S.A.F stilling basin (Full design: chute blocks, baffle blocks, end sill, and side walls) and draw a full details of a single chute block and baffle block using the given data (Note: use the attached chart): Flow discharge per unit width (q)= 24 m²/sec. Head loss throughout the basin (HL) 1.5 m. Ex-7.2 m. Basin width at the end sill (BE)- 20 m. Tail water depth-6 m. Slope of the glacis- 30°. Flaring (1:2) 1:6.