Answered: What acoustic frequency is required of… | bartleby

Related questions

Question

answer fast I will give upvotes

\What acoustic frequency is required of a plane acoustic wave in an acousto-optic cell so that a beam from a He-Ne laser is deflected by ?

Consider the case of

(a) flint glass for which the sound velocity is 3km/s and n=1.95 and

(b) sapphire crystal with the sound velocity of 11km/s and n=1.76.

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

a on (0) light is incident per pendicularly sus pended in air. The shortest thick ness thin The wavelength of of light tilm that produces fully cons tructive in terferen ce of refe cted is 500nm. the light iS 0.1 What is the in dix of re fra ction of the thin film ?
A multimode step index fiber has a relative refractive index difference of 1% and a core refractive index of 1.46. The maximum optical bandwidth that may be obtained with a particular source on a 4.5 km link is 3.1 MHz. (a) Determine the rms pulse broadening per kilometer resulting from chromatic dispersion mechanisms. (b) Assuming waveguide dispersion may be ignored, estimate the rms spectral width of the source used, if the material dispersion parameter for the fiber at the operating wavelength is 90. Q.3/
A given crystalline material has 3 atoms per lattice point. (i) How many acoustic phonon modes are there? (ii) How many of these are transverse, and how many longitudinal?
Optical Power. Show that the optical power flow in the z direction associated with the TE mode E,(y, z) = amUm (y) exp(-jßm²) is (|aml²/2n) cos 0m, where 7ŋ = No/n and no = VHo/€, is the impedance of free space.
Is it possible to produce interference effect between the o-ray beam and e-ray beam, which are separated by a calcite crystal from a unpolarized incident beam by recombining them? Explain your answer with proper justification.
4.1. A silica multimode step index fiber has a core refractive index of 1.46. Determine the optical loss in decibels due to Fresnel reflection at a fiber joint with: (a) a small air gap;: (b) an index-matching epoxy which has a refractive index of 1.40. It may be assumed that the fiber axes and end faces are perfectly aligned at the joint. Ans. (a) 0.31 dB; (b) 3.8 x 10-4 dB 4.2. The Fresnel reflection at a butt joint with an air gap in a multimode step index fiber is 0.46 dB. Determine the refractive index of the fiber core. Ans. 1.59
A radiometer has two square vanes (1.0 cm by 1.0 cm), attached to a light horizontal cross arm, and pivoted about a vertical axis through the center, as shown in the figure. The center of each vane is diboth from the axis. One vane is silvered and is perfectly reflecting. The other vandit blaakeros and and pivated aboutna trtice with intensity of 500 W/m is incident perfectly perpendicular to the front of both vanes. 1. Calculate the radiation pressure on the reflecting side. Then, using the fact that Pressure = Force/Area, calculate the total force on the reflecting side. 2. Do the same as part (a) for the absorbing side. 3. Now, recall that torque,, where r is the distance from the axis of rotation. Using your answers to (a) and (b). calculate the total torque on the radiometer. Keep in mind that the two torques will oppose each other because they are on opposite sides of the axis!
I need the answer as soon as possible
If the polypropylene has a refractive index of 1.5, what the wavelength of the laser light whose wavelength in the air is 790 nm would be in the propylene?
A filter is used to obtain approximately monochromatic light from a white source. If the pass band of the filter is 10 nm, Defining the coherence length and time, find the coherence length and coherence time of the filtered light? The mean wavelength is 600 nm.
h) The difference in arrival time between wave-packets with centre frequencies of ω1 and ω2 is Δt. What is DM in terms of Δt ?
I need the answer as soon as possible

SEE MORE QUESTIONS