We make a cut through BC, BF, and FG. The free-body diagram of the section to the left of the cut is shown. All members of the truss are assumed to be in tension. Find the force in BF. You can do this with one carefully chosen equation. The force is positive if in tension, negative if in compression. 5.6 kips Answer: BF 2.3 kips BC BF FG kips

We make a cut through BC, BF, and FG. The free-body diagram of the section to the left of the cut is shown. All members of the truss are assumed to be in tension. Find the force in BF. You can do this with one carefully chosen equation. The force is positive if in tension, negative if in compression. 5.6 kips Answer: BF 2.3 kips BC BF FG kips

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the load P that can be applied at C if the stress in the steel rod is limited to 37 ksi and the vertical movement of end C must not exceed 0.1 in. Let a = 3 ft. and b = 2 ft. Consider only the load based on the deformation at C. Answer must be in kips. Steel L= 4 ft A = 0.50 in? E = 29 x 10° psi a ft. b ft.
Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a positive number if the member is in tension, negative if in compression. ㅏ 20 KN H 34KN G -4 panels at 8 m- 28 KN D F E
Give me right solution according to the question.
Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. B 15' C 15' D 14' A 15' G F 56° E 14 kips Answers: BC = kips CG = kips %3D
Figure 1 shows a pin-connected truss system with pin supports at points A and B. Member AC has an area of 60 mm², E= 200 GPa, and yield stress oy= 150 MPa; Member BC has an area of 35 mm², E= 200 GPa, and yield stress oy= 200 MPa. A force is applied horizontally at point C as shown in the figure, with corresponding displacement A. Draw the complete F versus A response up to collapse and calculate the over-strength of the system. A B mom топп 60° 2 m F, A C
Compound axial member ABC has a uniform diameter of d = 1.2 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 80 in. and L2 = 140 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.10 in. LI L2 A d Aluminum Copper Answer: P = i B kips
In the truss shown below, what is the value of force in member AB? (note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative for compression. FAB = N 2000 N 3 m 2 m 2 m - 2 60°
Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive if in tension, negative if in compression. 21° BC= 60 G Answers: i BE= i BF= i A 60° F 60° B L L 60° 60⁰° 60⁰ D L
Determine the force in each member of the truss loaded as shown below. State if the members are in tension orcompression. Tabulate the result of your analysis.
Rigid bar DB in the figure is supported at pin B by axial member ABC, which has a cross-sectional area of A1 = A2 = 85 mm², an elastic modulus of Ej = E2 = 1000 MPa, and lengths of L = 390 mm and L2 = 645 mm. Aload of Q = 555 N is applied at end Cof member (2), and a load of P = 1425 N is applied to the rigid bar at a distance of a = 85 mm from pin support D and b = 45 mm from pin B. Determine the magnitudes of the downward deflections of: (a) pin B. (b) pin C. A |(1) Rigid bar B a b. L2 (2) (a) VB = i mm (b) vc = i mm
Compound axial member ABC has a uniform diameter of d = 2.1 in. Segment (1) is an aluminum [E1 = 10,000 ksi] alloy and segment (2) is a copper [E2 = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L1 = 74 in. and L2 = 135 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.40 in. %3D L1 L2 A d Aluminum В (2) Copper Answer: kips P = i
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP