Compound axial member ABC has a uniform diameter of d = 1.2 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 80 in. and L2 = 140 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.10 in. L₁ L2 A d Copper Answer: P = i (1) Aluminum B kips

Compound axial member ABC has a uniform diameter of d = 1.2 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 80 in. and L2 = 140 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.10 in. L₁ L2 A d Copper Answer: P = i (1) Aluminum B kips

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3 For the compound beam shown in Figure 4, determine the reaction forces, calculate the stress in each member, and determine the deformation in each beam using the Direct Stiffness Method. 3 ft 2 ft 2 ft y 500 lb 300 ft-lb 1= 0.948 in ¹ E = 30 106 psi I = 0.198 in ¹ E = 30-106 psi
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 38 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 5.16 kips 4.86 kips 2.48 kips 3.88 kips O 4.09 kips (1) B 3 ft P 8 ft 1.5 ft
CN=44
Determine the stresses in each bar and the bond reactions.
As shown in the figure, rod AB is steel and rod BC is an aluminum, are hinged to rigid suppots which are pinned together at B to carry a vertical load P=20kN. Each rod has a cross-sectional area of 400mm^2 and Es=200000Mpa and Ea=70000Mpa. Compute for the deformation of steel and aluminum and for the horizontal and vertical displacements of point B.
roblem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooled? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. roblem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D• A
A two member truss ABC is shown in the figure. The force (in kN) transmitted in member AB is - A 11 0.5 m 17 1pc C 1 m B 10 kN
HELP PLEASE NEED ANSWERS
A steel rod having a length of 50m is suspended vertically from one end. It supports a tensile load of P = 250 kN at the lower end. The unit weight of the steel is 7850 kg/m^3. The allowable tensile stress for steel is 140 MPa. Use E = 200 GPa. Determine the total deformation of the steel rod.
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D