Answered: Water pressurized to 6.5 × 10° Pa is…

Name: Water pressurized to 6.5 × 10° Pa isflowing at 5.0 m/s in a pipe whic
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Water pressurized to 6.5 × 10° Pa isflowing at 5.0 m/s in a pipe whichcontracts to 1/3 its former area.What is the pressure and velocity ofthe water after the contraction?Select one:O A. 2.5 x 10° Pa, 15.0 m/sO B. 4.5 × 10 Pa, 1.5 m/sO C. 3.0 × 10°

Science

Physics

Water pressurized to 6.5 × 10° Pa is flowing at 5.0 m/s in a pipe which contracts to 1/3 its former area. What is the pressure and velocity of the water after the contraction?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Water, pressurized to 3.00 × 10 5 Pa, flows through a pipe at 5.25 m/s. Somewhere along its length, the pipe contracts to 1/2 of its former cross sectional area. What are the pressure and speed of the water in the narrower portion of the pipe? (Density of water = 1 × 10 3 kg/m 3.)
Y2 Fresh water is flowing through this pipe at 2.00 m/s at the lower point, which is positioned 2.00 m above the floor in a water treatment plant. As the pipe rises the cross-sectional area is reduced by a factor of 3. The upper portion of the pipe is 8.00 m above the floor. If the pressure in the lower section of the pipe is 2.50 x 10° Pa, what is the pressure in the pipe at the higher position?
Please help me
An Oil refinery needs to pump oil of different densities from the import truck to its holding tank 13 meters above the ground. If they use a pump that can produce 2.2 atms of pressure, what is the highest density fluid that they can lift to that height? Give answer in kg/m3
Water is moving with a speed of 4.9 m/s through a pipe with a cross-sectional area of 4.9 cm2. The water gradually descends 9.0 m as the pipe increases to 8.8 cm2. (a) What is the speed at the lower level? (b) If the pressure at the upper level is 1.8 × 105 Pa, what is the pressure at the lower level?
In order to take a nice relaxing bath after this final, you fill up a bathtub with warm water. To fill the tub, water travels at 9 m/s in a pipe under your house. The faucet (where the water exits into the tub) in your house has a diameter twice that of the pipe under your house. The water pressure in the pipe/faucet is the same everywhere. (a) What is the height of your faucet, relative to the pipe under your house? (b) Let's do some special cases sensemaking! If the diameter of the faucet were the same as the diameter of the pipe under your house and the pressure was the same everywhere, what would the height differ ence need to be? explain.
Water travels through a pipe at 12.7 m/s. The pipe contracts from a crossectional area of 2.2 m2 to an area of 0.367 m2.What is the speed of the water in the second part of the pipe in m/s? m/s How much is the pressure change in KPa as the pipe contracts? The density of water is 1000 kg/m3. Enter a positive value for an increase in pressure, a negative value for a decrease. kPa
A horizontal pipe carries a smoothly flowing liquid of density of 1290 kg/m3. At Locations 1 and 2 along the pipe, the diameters are ?1=6.97 cm and ?2=2.65 cm, respectively. Is the flow speed at Location 2 higher or lower than the flow speed at Location 1? cannot tell from the data higher lower The flow speed at Location 1 is 1.39 m/s. What is the pressure difference Δ? between Location 2 and Location 1 (including its sign)? Ignore viscosity. Δ?= Pa Is the pressure at Location 2 higher or lower than the pressure at Location 1? lower higher cannot tell
A horizontal pipe decreases uniformly from 150 mm diameter to 100 mm diameter in the direction of the flow of water. The pressure at the narrow section of the pipe is 2.2×105 N/m2, when the flow rate is 0.12 m3/s . Assuming there are no friction losses, calculate the pressure at the 150 mm side.
Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is 1.85 x 105 Pa and 1.20 × 105 Pa. The radius of the pipe at points 1 and 2 respectively is 3.50 cm and 1.50 cm. If the vertical distance between points 1 and 2 is 2.75 m, determine the following. (a) speed of flow at point 1 m/s (b) speed of flow at point 2 m/s (c) volume flow rate of the fluid through the pipe m³/s y
Water flows through the vertical pipe such that when it is at A, it is subjected to a pressure of 150 kPa and a velocity of 3 m/s. Determine the velocity and pressure at B as a function of the pipe diameter d. Plot the pressure and velocity versus the diameter for the range of values 25mm ≤ d ≤ 100 mm with a step of 25 mm increment. C -100 mm
A pipe is tapered so that the large end has a diameter twice as large as the small end. What must be the gauge pressure (the difference between pressure at the large end and pressure at the small end) in order for water to emerge from the small end with a speed of 12 m/s if the small end is elevated 8 m above the large end of the pipe?