Water from a reservoir flowing through a non rigid 600mm diameter pipe with a velocity of 2.m/s is completely stopped by a closure of a valve situated 1050m from the reservoir. The pipe thickness is 18mm. Bulk modulus of elasticity of water is 2000MPa and modulus of elasticity of steel is 200000MPa. A.) Compute the velocity of soundwave Choices: 1724.47 1442.47 1224.74 2441.74 B.) Determine the pressure due to instantaneous closure (KPa) Choices: 2449.49 4229.94 2994.94 4922.49 C.)Determine the pressure due to a closure that takes place in 5 seconds. in KPa Choices: 408 804 840 480 Note:please help me in the sample problem and please base ypur answer on the given choices thank you

Q: PROBLEM 3: In DYN-002, a 20-pound sphere attached to a 4' cord at a 30-degree angle with the…

A: T= 57.3 lb N= 59.3 lb

Q: A 6-cm-diameter horizontal stationary water jet having a velocity of 40 m/s strikes a vertical…

A:

Q: A C-channel has a dimensions of as shown, in mm, with a thickness of 75 mm. Determine the moment of…

A:

Q: A flat plate is placed normal to a discharging jet of water. The jet discharges water at the rate of…

A: Given- Rate of discharge from jet Q= 0.2 m3/s, Speed of water V= 18 m/s, It is needed to find the…

Q: A circular bar having 200 mm2 area is subjected to axial loads as shown in Fig „Find the value of (…

A:

Q: Determine the horizontal deflection of D. Fy-20.00 B Fx=10.08 3.0 m A C 4.0 m D 3.0 m Consider the…

A:

Q: 19. A circular pipe of diameter 0.5 m carries the discharge of 50 litres/s. The head loss due to…

A:

Q: Draw the simplified idealization of a damped SDOF system under free vibration with the following…

A: Let's choose the the second type of idealization given  M= 2000 kg k = 23000 N/m c = 500 N-s/m u(0)…

Q: 1. Draw the Shear and Moment Diagram of the given beam. A 1m 1m B 2m 1m A 1m

A: Given data  A = 13 kN  B = 10 KN/m  Draw Shear Force Diagram (SFD) and Bending Moment Diagram (BMD)…

Q: Part 4 (problem solving) Problem 1 Calculate sag correction for a 30 m steel tape under a pull of 80…

A:

Q: PROBLEM 1 A 22.7 kg door is supported on rollers A and B resting on a horizontal track a shown. A…

A: The given data is: Constant force, P=45 N Weight of the door, m=22.7 Kg

Q: 24. 19. A circular bar one metre long and 8 mm diameter is rigidity clamped at one end ir vertical…

A: Given data, Length of bar l = 1 m Diameter of bar d = 8 mm Radius of bar a = 4 mm Applied couple c =…

Q: Water from a reservoir flowing through a non rigid 600mm diameter pipe with a velocity of 2.90m/s is…

A:

Q: 10 m/s E,=200 GPa E,=105 GPa 50 kg Steel 15 mm-diaBrass k=25 kN/mm 1.5m 1.5m 0.5m OZoom image…

A:

Q: 26. A block with a mass m is placed on the top of an identical block m and the system of two blocks…

A: For the upper block -  N1 = mgandF1 = μsN1⇒F1 = μsmg       .....1   For the bottom block -  N2 =…

Q: heres the question:A 100- m steel tape is used to measure the distance of the line and found to be…

A:

Q: ☆☆ 1. A wrench is used to twist a bolt. A force of 60 N is applied in a clockwise direction at 80°…

A: Given: Force, F=60 N Position of vector, r=20 cm angle, 80o

Q: B. 3920 C. 5090 erted by the jet on the vane if th B. 2460 C. 2365 eted by the jet on the vane if…

A: solution of above problem is below:

Q: 9. A 50 meter steel tape was standardized and supported throughout its whole length and found to be…

A:

Q: For the beam shown in the figure below, draw the influence lines for Ra, Rc, Re, Vb and Mb and…

A:

Q: A horizontal aluminum rod 2.6 cm in diameter projects 5.0 cm from a wall. A 980 kg object is…

A:

Q: 2. What is the magnitude of moment about point O? a) 150 Nm b) 300 Nm c) 410 Nm d) 260 Nm O F₁ = 400…

A: Given Data  Find the moment about point- O.

Q: Find the minimum value of friction factor than can occur in laminar flow through a circular pipe.

A:

Q: I measuring a dis of 1000 ft when the temperature of the tape is 32°E? 11.7 An aluminum wire is…

A:

Q: (a). Obtain the total elongation of a steel bar of cross-sectional Area 1250mm acted upon by forces…

A:

Q: ater from a reservoir flowing through a non rigid 600mm diameter pipe with a velocity of 2.90m/s is…

A:

Q: X A 90 mm ww 001 F 70 mm B

A: The ans is attached below:

Q: The 30kg rectangular plate shown in the given figure is suspended by its center from a bar whose…

A:

Q: TUATION IV (9-10) The beam AB shown in the figure supports a uniform loa ting all over half the…

A: To find value of W for the equilibrium

Q: A 2.0 m long metal wire is loaded, resulting in a 4 mm elongation. Find the change in diameter of…

A:

Q: An engineer used a 30 m tape in measuring an inclined ground 459.20 m long. The difference between…

A: To determine:  The value of horizontal distance . Given Data: Length of tape=30mThe inclined ground…

Q: An experimental device imparts a force of magn- tude F = 225 N to the front edge of the rim at A o…

A:

Q: Problem 1: If the magnitude of the couple moment acting on the pipe assembly is 100 N.m, determine…

A: Given, Magnitude of the couple moment acting on the pipe assembly is 100 Nm We have to find F

Q: 27. Refer to Figure 13. What is the reaction at B? a. 275 N b. 375 N FIGURE 13 300 N/m c. 475 N d.…

A: the given beam is the imply supported determinate beam with loading is uniform varying load on the…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.