The initially stationary 22-kg block is subjected to the time-varying force whose magnitude P is shown in the plot. Note that the force is zero for all times greater than 4 s. Determine the time t, at which the block comes to rest. HR=0.44 Hg = 0.62 Answe: t = i 22 kg 4.256 P 28° P. N 153 S 0 0 1 4 t, s

The initially stationary 22-kg block is subjected to the time-varying force whose magnitude P is shown in the plot. Note that the force is zero for all times greater than 4 s. Determine the time t, at which the block comes to rest. HR=0.44 Hg = 0.62 Answe: t = i 22 kg 4.256 P 28° P. N 153 S 0 0 1 4 t, s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In the figure below, the slope angle theta = 20 degrees and the block weight equals 100 N. which of…

A: OPTION B -- Up Slope ( Parallel to the slope surface and upwards. )

Q: The initially stationary 24-kg block is subjected to the time-varying force whose magnitude P is…

A: Given data:- The given mass m = 24 kg Block. The force is zero then all-time greater than,=5 sec.…

Q: The 2.0-kg collar is at rest in position A when the constant force Pis applied as shown. Determine…

A: Given, Mass of the collar, say M = 2 kg Force applied on the collar, P = 33 N Vertical distance…

Q: For the beam and loading shown, using the double integration method, determine the vertical reaction…

A: Given:To find:The vertical reaction at A

Q: Initially a 7-kg block is rotating with a constant speed of 2 m/s around the circular path centered…

Q: The tongs are used to lift the 150-kg crate, whose center of mass is at G. Suppose that 0 = 26 °.…

A: Answer The least coefficient of static friction at the pivot blocks so that the create can be lifted…

Q: The 2.5-kg collar is at rest in position A when the constant force Pis applied as shown. Determine…

Q: Answer fast.

A: Given:r=670mm=0.67m (radius of the blade)θ¨=4.2rad/s2 (angular acceleration)θ˙=0rad/s (angular…

Q: Replace the loading system at point 0. 0.2 m -1.5 m- 30° 450 N 2m 200 Nm Counterclockwis

Q: ims for the beam loaded with both the distributed load and the couple. Then answer the questio 2.1…

Q: Problem 2: The 2-kg collar is released from rest at A and slides down the inclined fixed rod in the…

A: Solution-The given values are as follows Collar Mass=2kgCoefficient of kinetic friction=0.4To…

Q: Q: The cross section of oil tank with a slanted bottom as shown in the figure. A rectan door 600 mm…

A: Solution force R = 1377.32 N acts at distance of 655.10 mm from free surface

Q: Dětérmine the magnitude of the force P, acting as shown, that will cause the 120 N crate to move.…

A: Weight of body, coefficient of static friction is given and it has been asked to determine minimum…

Q: The 80 kg crate has its center of gravity at G. Determine the smallest force P that will initiate…

Q: 2. A steady flow between two parallel plates is fully developed and laminar. The distance between…

A: Solution: a) Derivation of velocity distribution, u: Consider a steady flow between two parallel…

Question

The initially stationary 22-kg block is subjected to the time-varying force whose magnitude P is shown in the plot. Note that the force
is zero for all times greater than 4 s. Determine the time t, at which the block comes to rest.
HR = 0.44
Hg = 0.62
Answe: ts=
i
22 kg
4.256
P
28°
P, N
153
S
T
4
t, s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

24 mm/s Q2) When the force P is applied to the plate, the velocity profile for a Newtonian fluid that is confined under the plate is approximated by u = 12y4 mm/s, where y is in mm. Determine the minimum shear stress within the fluid. Take u = 0.5 x 10-3Pa.s.
Problem 1. Determine the smallest force P needed to lift block B. The coefficient of static friction between A and C and between B and D is us = 0.3, and between A and B is µ's= 0.4. Neglect the weights of A and B. 3000 Ib B 15 P- A C
The question is in the picture. Thanks
1. Consider a water jet having a diameter of D = 1 cm and a flow of Q = 1 L/s. The jet is deflected by a fixed plate which is inclined at an angle of 50° from horizontal. a) Determine the velocity vx in the x-direction in m/s. b) Determine the velocity vy in the y-direction in m/s. c) Determine the resultant force Fx on the plate in the x-direction in N. d) Determine the resultant force Fy on the plate in the y-direction in N. e) Determine the combined resultant force F on the plate in N. 1 L/s 50° V = 6 m/s
The block slides at a constant speed on a surface with friction. In each case, the water jet has velocity 50 m/s and cross-sectional area 5 cm2, and the block has velocity 25 m/s. In case (a), the jet is deflected to an angle of 60° from horizontal relative to the block, as shown. In case (b), the jet is deflected 180°. Calculate the friction force in each case. Apply both a moving Reference Frame (RF) and a fixed RF. Use the VSM. Check that both RFs give the same friction force for a given case. (We would not expect the two cases to have the same friction force!) Density of water is 1000 kg/m3. All jets are open to the atmosphere. case (a) 60° case (b)
Q2: 1.2 D.L x l.6 L.L Mu A: Find the maximum value of (p) that can be applied to the beam shown. Use f. =21.7 MPa and fy = 350 MPa (WD.L is included the self-weight of beam). %3D b hy P Wu =7 kN/m D.L 2028 A 500 mm 4028 250 mm -7.5 m-
PLEASE DO IT RIGHT THIS IS MY 3RD TIME!!!
Statics
The 300-N block in the figure is at rest on the rough horizontal plane before the force P is applied at t = 0. The magnitude of P is 80t N, where t is the time in seconds, and its direction is constant. The coefficients of static and kinetic friction are µ̟ = 0.40 and µk = 0.20, respectively. Which of the following most nearly gives velocity of the block after 5 seconds? 300 N P = 80t N
Problem No. 1 Determine the smallest force P subjected at the wedge B that is required to lift the B Newton crate A. The coefficient friction at all contacting surfaces is E÷100. Neglect mass of the wedges and the friction between the crate A and the wall. Substitute: B=465, P THE E=22, H=12
A wooden beam 150 mm wide by 300 mm deep is loaded as shown. fb = 8 MPa a) Determine the maximum capacity of the beam. b) Determine the value of maximum value of P if x is 2m.