ELEVATION 20MELEVATION30mAIR Po?150mmøSG-0.84Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84)(А) 82.19 КРав) 87.74 КРас) 98.23 КРаD) 93.30 КРаE) 76.49 KPa

Given:- head loss from point 1 to point 2= 600mm diameter=150mm SG of oil=0.84 flow=17L/s To find:-…

Answered: Oil flows from a tank through a 150mm…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PLEASE SHOW COMPLETE SOLUTION WITH FIGURE IF APPLICABLE
Subject: Hydraulics/Fluid Mechanics A closed compartment shown contains water h= 5 m deep at the left side and H =10 m deep on the right side. If the pressure at point A is 75 kPa abs on the closed compartment, what is the absolute pressure in kPa of point B if neglecting weight of air.
An open jet of water at 20 ℃ exits a nozzle into sea-level air and strikes a stagnation tube, as shown in the sketch. If the pressure at the centerline of section (1) is 110kpa (abs), and losses are neglected, estimate: (a) the mass flow in kg/s, and (b) the height H of the fluid in the stagnation tube. (Atmospheric pressure =101.3 kpa)
just answer quickly
civil engineering.
b) Two pipes (at points A and B) have been connected with the manometer as shown in Figure Q1. i) Determine the pressure at point B if the pressure at point A is 10 kPa. ii) If pipe at point B is not connected with the pipe and open to the atmosphere, what happens to the current manometer? A. B. 0.3 m Water Spesific Weight for Air = 11.43 N/m³ 3 m Oil (sg = 0.86) Figure Q1: Compound manometer
As shown in the figure, a pump draws water from reservoir A (EI 25m) and lifts it to reservoir B (El 60m). The loss of head from A to 1 is 2 times the velocity head in the 200 mm pipe and the loss of head from 2 to B is 10 times the velocity head in the 150 mm pipe. Calculate the pressure head at point 1 when the discharge is 0.030 m³/s. Round off your answer to one decimal place. E1 25 7 Pl Answer: = 4 200 mm 2 m 150minh EL O El 60 B
2. Water and oil flow in horizontal pipelines. A double U-tube manometer is connected between the pipelines, as shown in figure below. Calculate the pressure difference between the water pipe and the oil pipe. * Air Oil 25 mm Water 150 mm Sz =0.9 250 mm S =1.6
The 275-kg circular craft is suspended 100 mm from the ground. For this to occur, air is drawn in at 18 m/s through the 200-mm-diameter intake and discharged to the ground as shown. Take Pu = 1.22 kg/m³. Assume the fluid is an ideal fluid, that is, incompressible and frictionless. (Figure 1) -1.5 m -1.5 m -200 mm B 100 mm Determine the pressure that the craft exerts on the ground. Express your answer to three significant figures and include the appropriate units.
The cage system shown in the figure is made of EC rod. The Flow Limit of the material is 180 MPa and the Safety Coefficient is 4 is desired to be. Accordingly, the circular cross section EC rod Calculate the diameter.
Pressure gage B is to measure the pressure at point A in a water flow. If the pressure at B в is 87 kPa, estimate the pressure at A, in kPa. Assume all fluids are at 20°C. ywater =9790 N/m', Ymercury =133100 N/m2, yoil =8720 N/m³ SAE 30 oil Gage B Mercury 6 cm 5 cm Water flow 11 cm 4 cm
1.) A pressure in a given tank reads 398 mm of Hg. Determine the equivalent height of a certain fluid in m with sp.gr= 4.33.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2 is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84)