Situation 2: The figure shown below shows a pump drawing water from a reservoir and discharging it into the air at point B. The pressure at point A in the suction pipe is is a vacuum of 10 in mercury and the discharge is 3 ft³/s. Determine the total head at point A and B with respect to a datum at the base of the reservoir. 10-in-diameter suction pipe 8-in-diameter discharge pipe Pump 15 f 25 ft 40 ft

Situation 2: The figure shown below shows a pump drawing water from a reservoir and discharging it into the air at point B. The pressure at point A in the suction pipe is is a vacuum of 10 in mercury and the discharge is 3 ft³/s. Determine the total head at point A and B with respect to a datum at the base of the reservoir. 10-in-diameter suction pipe 8-in-diameter discharge pipe Pump 15 f 25 ft 40 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use four decimal places in all solution
Solve last three parts where density of fluid is 900kg/m3
topic: parallel pipes hydraulics
Hydrodynamics pumps (WRITTEN COMPLETE SOLUTION AND FIGURES IF NEEDED) 1. A centrifugal pump installation draws water from an open reservoir having a water elevation of 5 m above the pump centerline and delivers the water to another open reservoir 80 m above pump centerline. The rate of discharge is 600 li/min. The suction pipe has a diameter of 200 mm while that of the discharge pipe diameter is 150 mm. The friction loss at the suction is estimated to be 4 times the velocity head at the 200 mm suction pipe. At the discharge, the friction loss is estimated to be 21 times the velocity head at the 150 mm discharge pipe. If the overall mechanical efficiency is 77%, estimate the brake power input to thepump. a. brake power Answer : ____________________ kW
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
In the illustration: A В 2 D All friction factor f - 0.02 All pipe lengths L- 250m Diameter of Pipe A= 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.
Please answer and explain both questions in full detail
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
Water is pumped from a supply reservoir to a ductile- iron water-transmission line, as shown in Figure 2.26. The high point of the transmission line is at point A, 1 km downstream of the supply reservoir, and the low point of the transmission line is at point B, 1 km downstream of A. If the flow rate through the pipeline is 1 m3/s, the diameter of the pipe is 750 mm, and the pressure at A is to be 350 kPa, then: (a) estimate the head that must be added by the pump; (b) estimate the power supplied by the pump; and (c) calculate the water pressure at B. Supply reservoir Elev. 7 m Pump Elev. 10 m Transmission line Elev. 4 m- B Figure 2.26: Water pumped into a transmission line
An oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a pressure tank pushing the oil through 200 m of new ductile iron pipe (DIP: 15 cm diameter, square-edged entrance) to point "2" (atmospheric pressure) as shown in Figure P3.11.11. The sur face of the fluid in the tank (point "1") is at elevation 100 m and the end of the pipe (point "2") is at elevation 106 m. What air pressure will be needed over the fluid to produce the requisite flow? (S.G. (oil) = 0.84, v 2.03 x 106 m²/s, and e = 0.00012 m.)
Determine the discharge in pipes 1, pipe 2, pipe 3 and pipe 6 in the system shown if the total head loss from A to B is 100m and friction factor for all pipes is 0.02.