Water flows steadily from one location to another in the inclined pipe shown in the figure below. At one section, the static pressure is 9.5 psi. At the other section, the static pressure is 5.0 psi. Which way is the water flowing ("1" depicts down, "O" - otherwise)? Water flows steadily from one location to another in the inclined pipe shown in the figure below. At one section, the static pressure is9.5 psi. At the other section, the static pressure is 5.0 psi. Which way is the water flowing ("1" depicts down, "O" - otherwise)?p= 9.5psi•1085ftP=5.0psi

Step 1: We use Bernoulli's theorem to solve this problem, according to Bernoulli's theorem…

Water flows steadily from one location to another in the inclined pipe shown in the figure below. At one section, the static pressure is 9.5 psi. At the other section, the static pressure is 5.0 psi. Which way is the water flowing ("1" depicts down, "O" - otherwise)? p= 9.5psi • 10 85ft P=5.0psi

Water flows steadily from one location to another in the inclined pipe shown in the figure below. At one section, the static pressure is 9.5 psi. At the other section, the static pressure is 5.0 psi. Which way is the water flowing ("1" depicts down, "O" - otherwise)? p= 9.5psi • 10 85ft P=5.0psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: Water is flowing through an inclined pipe and two sections (section 1 and section 2 ) of the pipe are considered. The diameter of the pipe at section 1 is (200 + 33 ) mm and (120 + 33 ) mm at section 2. The elevations of the sections 1 and 2 above datum are (800 + 33) cm and (400 + 33 ) cm respectively. If the pressure at section 1 is 40x104 N/m? and the discharge through the pipe is 60 litres per second, calculate the intensity of pressure at section 2. /
NEED HELP. PLEASE ANSWER ASAP. WILL UPVOTE
The pipe elbow below discharges water at rate of SN/100 (m/s) into the atmosphere at section 2 (where SN = 21). The total volume of the passage between section 1 and 2 is equal to 0.2 m3 and the total mass of the elbow material between section 1 and 2 is equal to 10 x SN (kg). Neglect any friction losses. Calculate the horizontal and vertical forces acting on the elbow. Also calculate the resultant force and angle of force on the elbow. SN=21
UPVOTE WILL BE GIVEN! Write the solutions legibly and correctly. Answer in 3 decimal places. HYDRAULICS/FLUID MECHANICS
If the gate was designed to withstand a maximum force of 6,000 lbs, verify the gate will not break when the tank is filled with gas.
Topic: Fluid mechanics Compute: Horizontal force exerted on ABC by the oil and water. FINAL ANSWER MUST BE: 3 decimal places and unit is kN Thank you!
P4
Hi kindly answer the problem attached image below. Thank you!ASAP.
Required information A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate mof 35 kg/s. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the density of water to be 1000 kg/m³ and the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. 50 cm Water m kg/s DATUM: Assume positive up and to the right Determine the anchoring force needed to hold the elbow in place. N. PALLE The anchoring force needed to hold the elbow in place is The resultant direction of the force is
Water is flowing steadily in a horizontal elbow and nozzle combination shown in the figure. The gage pressure at section (1) is 100 kPa with inlet velocity of 2 m/s. At section (2) the water exits to the atmosphere. Neglecting pipe weight, determine the magnitude and direction of the x and y components reaction forces exerted on the flanges to withstand this flow. 160 mm y section (2) 300 mm V1 -> section (1) P, = 100kPa V, = 2m/s
A differential pressure below is receiving 5 psi (gauge) on one side and 16.2 psi (absolute) on the other. What pressure does the sensor report?
8. The following figure shows a tank of water with a circular pipe connected to its bottom. A circular gate seals the pipe opening to prohibit flow. To drain the tank, a winch is used to pull the gate open. Compute the amount of force that the winch cable must exert to open the gate. - Winch Cable- Water Stop 30⁰ 38 in -Hinge Circular gate 10.0 in diameter Open pipe