Water flows from tank A to tank B, as shown in Figure Q4. By neglecting all minor losses and assuming friction factor of 0.01 for all pipes, find the flowrate into tank B when the valve is opened to allow water to flow into tank C. Elevation 15 m Diameter of each pipe 60 m. m20 m 0.10 m Elevations ==

Water flows from tank A to tank B, as shown in Figure Q4. By neglecting all minor losses and assuming friction factor of 0.01 for all pipes, find the flowrate into tank B when the valve is opened to allow water to flow into tank C. Elevation 15 m Diameter of each pipe 60 m. m20 m 0.10 m Elevations ==

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Water is pumped through three pipes in series. Compute the discharge if the power delivered to the pump is W₂ = 1920 kW and the pump efficiency is n = 82%. The pipe resistance coefficients are R₁ = 13.2 s²/m³, R₂ = 204.1 s²/m³, R₂ = 25.8 s²/m³, and the head difference between the downstream and upstream reservoirs is 50 m. Ans: Q = 0.792 m³/s
Oil is being pumped from an Open Tank A (elev = 110m) to another Open Tank B (elev = 220m) with a total head loss of 15m of Oil. The pump has a power rating of 210kW and an efficiency of 65%. Pipe 1 (D = 200mm) connects Tank A and the pump while Pipe 2 (D = 150mm) connects the pump and Tank B. Calculate the pump head, velocity of flow in Pipe 1, mass flowrate in Pipe 2, power output of the pump and volumetric flowrate of oil.
Please give a detailed Handwritten solution.
Two pipes in a series have a flow rate of 50 L/s. The pipe upstream is 300 mm and reduced downstream to 150 mm. Determine the velocities for both diameters in m/s. Consider the centerline of the pipes along a horizontal datum reference. Ignore losses.
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
Answer asap. will upvote
An air-conditioning system is designed to have a ductwith a rectangular cross section 1 ft by 2 ft, as shown. Duringconstruction, a truck driver backed into the duct and made it atrapezoidal section, as shown. The contractor, behind schedule,installed it anyway. For the same pressure drop along the pipe,what will be the ratio of the velocity in the trapezoidal duct tothat in the rectangular duct? Assume the Darcy-Weisbach resistance coefficient is the same for both ducts.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
Determine the power requirement of the pump shown in Figure 3.0, assuming it has an efficiency of 88%. The system has a loss coefficient of 3.0 up to point A, and K =1.2 from point B to point C. Neglect any losses through the exit nozzle. Additionally, compute the pressures at points A and B. Water 15 m 2 cm 4 cm dia. 5 cm dia. Figure 3.0 400 kPa
Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and then is suddenly reduced to 50 mm for the next 9 m. The difference of levels between the tank water levels is 2.40 m. Pipe coefficient f=0.005 and the contraction coefficient at sudden change in area is 0.58. Find all the losses, in terms of velocity v2 at exit from the 50 mm2pipe and hence find rate of flow. Draw the Hydraulic gradient line.