Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 90o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be neglected

Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 90o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be neglected

Name: Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in whic
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 90o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be negl

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.114P: Determine the resultant force acting on the elbow of the thin-walled pipe when the pipe carries a...

See similar textbooks

Similar questions

The diameter of a pipe line is 6 inch at A and 18 inch at B. A is 11 ft lower than B. If the pressure at A is 10 lb per sq in and at B 7 lb per sq inch when the gasoline (sp gr = 0.728) flow is 2.5 cfs, determine the friction loss between A and B.
In a tapered horizontal pipeline, the seawater's speed is 3.75 m/s and the gauge pressure is 21 kPa at the first point. Find the gauge pressure at a second point in the line if the cross-sectional area at the second point is thrice that at the first.
The water flows from the nozzle through a 180-degree elbow. For example, the pipe diameter D-75mm, the nozzle diameter d=25mm, and the pressure gauge at the front of the pipe reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint 1-1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm, the weight of the elbow and the water is 100N, and the acting position is shown in the figure.
Three hundred and eighty five gallons of water per minute is flowing through a 4.3-in radius horizontal pipe. If the bore of the pipe is reduced to 2.7-in radius and the pressure in the smaller pipe is 93 psig, what is the pressure in the larger section of the pipe? Include schematic diagram.
Water flows in a D = 36 mm diameter pipe as shown in the figure. Since Q = 60 m3 / h, and the density of %3D water is 1000 kg / m³, calculate the resultant force on the elbow and the angle it makes with the horizontal. 120°
The diameter of a pipe carrying oil(s=0.92) changes gradually from 400 mm at A to 600 mm at B. Point A is 3.6 m lower than B. If the pressure at A is 70 KPa and that at B is 49 KPa when 140 L/s is flowing, determine the direction of flow; (b) the frictional loss between the two points.
A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the pressure is 138 kN/m2. If the pipe tapers gradually from 150mm diameter at A to 100mm diameter at location B, determine the pressure of the water at B, assuming there is no loss of energy.
Water "bubbles up" above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 1.5- in.- diameter wrought iron pipe between point (1) and the exit is 44 inches. If the gage pressure at point (1) to produce this flow is 2 psi and h₂ = 4 in, determine the maximum height of the water jet h3. Data for water: Density = 1.94 slug/ft³; viscosity = 2.34x10-5 (lb/ft²).s O (2) (1)
In a container of diameter Φ (see image), a tube of diameter ε (much smaller than the diameter of the container) is connected at a height d. The water level in the container is h. Water flows at a constant speed in the tube. The density of the fluid is ρ. If the container is open to the air, calculate the pressure at the connection. Conceptual question: In the second figure of the image, three pressures are represented. Are these pressures constant along the height they describe?
QUESTION 2 Water flows through the horizontal branching pipe shown in Figure 3. Water discharges into the atmosphere at section (4). If viscous effects are negligible, a) determine the pressure at section (2). b) calculate the velocity at section (3). c) what is the x component of the anchoring force at the flange to hold the pipe in place? Draw the control volume and identify all forces. A2 = 0.007 m² V2 = 9 m/s (1) Flange 40° A = 0.1 m² V, = 3 m/s → P, = 69 kPa Az = 0.02 m² %3D P3 = 55 kPa (3) A4 = 0.0095 m². (4) Figure 3
If anyone can help with this problem I would appreciate it. Thank you!
As seen in Figure below, the water passing through the flanged connection system is discharged to the atmosphere from the outlets no. 2 and no. 3. Calculate the force acting on the flange in the x-direction according to the figures given in the figure. (Ignore the effect of gravity and the friction of the fluid with the wall).