Determine the magnitude and direction of the resultant force exerted on the double nozzle depictedin the figure, given that the pipes' axes and both nozzles lie in the horizontal plane, with both nozzlejets having a water velocity of 20 m/s.150 mm5 degree250 mm25 degree100 mm

Step 1: Step 2:Step 3:Step 4:Step 5:Step 6: Therefore, The resultant force is calculated as 4634.62…

Answered: Determine the magnitude and direction…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

simple answer no need to explain
Don't copy any wrong solution, Answer must correct. Show your work within 30minutes.
1. A water jetpack suspends a 7Okg man in air without motion along the vertical and the horizontal as the man tilts the platform. The jetpack has two outlets, each has a diameter of 5cm, and an inlet with a diameter of 6cm. Calculate the volumetric flowrate, in and out of the water jetpack, and the angle 00 such that there is no motion along any direction. Neglect the weight of the jetpack. The inlet is perpendicular to the outlet. inlet W W Qi 2Q. ВАCK SIDE
According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
Consider the bend shown in . The total mass of the bend and the water within it is 20 kg, with a mass center at point G. The pressure of the water at A is 50 kPa Assume that no force is transferred to the flanges at A and B. Suppose the velocity through the pipe to be 4.5 m/s. 100 mm By 60 100 mm 600 mm 150 mm- 100 mm D Part A Determine the horizontal component of force exerted on the fixed support D. Express your answer to three significant figures and include the appropriate units.
A straight horizontal pipe 100 mm in diameter terminates in a short, tapering nozzle from which a jet of water 50 mm in diameter is discharged to atmosphere. If the gauge pressure immediately before the nozzle is 50 kPa and friction in the nozzle is negligible, calculate the tensile force between the nozzle and pipe.
If anyone can help with this problem I would appreciate it. Thank you!
Help me please
Oil flows through the 100-mm-diameter pipe with a velocity of 8 m/s (Figure 1). The flow occurs in the horizontal plane. Take p = 900 kg/m³. ▼ Part A If the pressure in the pipe at A and B is assumed to be 90 kPa, determine the component of force the flow exerts on the elbow. Express your answer to three significant figures and include the appropriate units. ▾ View Available Hint(s) ▾ Hint 1. How to determine the component of force the flow exerts on the elbow Build a free body diagram of the control volume containing oil within the pipe and elbow between cross-sections at A and B. Then using the linear momentum equation determine the component of the force the flow exerts on the elbow. F₂ = Part B HÅ Submit Previous Answers Request Answer Value Fy = X Incorrect; Try Again; 4 attempts remaining Submit Units If the pressure in the pipe at A and B is assumed to be 90 kPa, determine they component of force the flow exerts on the elbow. Express your answer to three significant figures and…
An engineer designing a light aircraft is trying to make an estimate of the radius of the propeller needed. The design speed of the aircraft is 69m/s into still air and at this speed experience allows the engineer to assume a propeller efficiency of 0.8. Other analysis shows that a thrust of 9296N must be supplied by the propeller to maintain the design speed. Assuming a constant air density of 1.21 kg/m³, determine the radius of the ideal propeller in m to 2 decimal places. Note: Use the propulsive efficiency equation to find the final downstream speed of the air and check that this makes physical sense before calculating the radius.
Water under a gauge pressure of 350 kPa flows with a velocity of 5m/s through a right- angle bend that has a uniform diameter of 250mm. The bend lies in a horizontal plane and water enters from the west and leaves towards the north. Assuming no drop in pressure, what is the magnitude and direction of the resultant force acting on the bend?
Need help with this engineering problem. The answer needs to be in meters.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the magnitude and direction of the resultant force exerted on the double nozzle depicted in the figure, given that the pipes' axes and both nozzles lie in the horizontal plane, with both nozzle jets having a water velocity of 20 m/s. 150 mm 5 degree 250 mm 25 degree 100 mm