Air flows from a 5-mm diameter nozzle and it strikes a curved vane, which is in a vertical plane as shown in the picture below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all friction. Air Stagnation Fixed vane tube 5-mm diam. Open Free air jet 15 cm 45 Water 30⁰

Air flows from a 5-mm diameter nozzle and it strikes a curved vane, which is in a vertical plane as shown in the picture below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all friction. Air Stagnation Fixed vane tube 5-mm diam. Open Free air jet 15 cm 45 Water 30⁰

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 14.2 A jet of water (r = 1000 kg/m³) is deflected by a vane mounted on a cart. The water jet has a constant cross-sectional area, A = 50 cm², which is projected off the vane at an angle q = 30° with respect to the horizontal. The pressure everywhere within the jet is atmospheric. The incoming jet velocity (with respect to the ground) is Vjet = 4.5 m/s. The cart has mass 50kg. Determine: a. the forces, Fx and Fy required to hold the cart stationary Vjet Vcart Fy Fx b. the horizontal force component, Fx, if the cart moves to the right at the constant velocity, Vcart = 3 m/s c. the horizontal acceleration of the cart at the instant when the cart moves with velocity Vcart = 2.5 m/s if no horizontal forces are applied Ans: a) 10 N
Problem 5.32: (Munson, et al. 5th ed.) Determine the magnitude and direction of the anchoring force needed to hold the horizontal elbow and nozzle combination show in place. At section (2), water discharges into the atmospheric at 100 kPa and the pressure at location (1) is 100 kPa gauge. 160 mm V₂ Section (2)1 V₁ 300 mm Water Section (1) P₁ = 100 kPa V₁ = 2 m/s X
6.7. Calculate the force exerted by the water on this orifice plate. Assume that water in the jet between orifice plate and vena contracta weighs 4.0 lb. 0.75 0.20 10' d
Q1. What would be the effect on the calculated force on the flat plate if the jet were to leave the plate not horizontal but inclined upwards at an angle of 1 °? If the experiment were to be repeated with the vane in the form of a cone with an included angle of 60° (half angle 30°), how would you expect the results to appear?
Consider a pressure washer exerting a horizontal force on the wall (and the operator). Assume that water enters the pressure washer wand vertically. Output nozzle is 1/8" (0.125 inches) in diameter. A. What is the water pressure at the exit (once water leaves the nozzle)? b. Calculate the flow needed to produce 20lb of horizontal force.
contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P. 100 kPa water is 999 kg/m' and characteristic gas constant for V-0 air is 287 J/kg K. 25°C, O Test section 25°C (GATE) To manometer Fig. 6.6
Section 1 is the image below the problem
A special kind of jet is shot in the water. If the jet is going with acceleration 2 m/s/s. What is the pressure on the jet when it is 50 m deep from the surface? (Assume the pressure at water surface = 1 atm). 2 atm ○ 4.9 atm 1 atm 5.9 atm
Vanes 6.20 Determine the external reactions in the x- and y-directions needed to hold this fixed vane, which turns the oil jet in a horizontal plane. Here V, is 18 m/s, V, = 17 m/s, and Q = 0.15 m /s.