Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shown below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all friction. Air Open Water Stagnation Fixed vane tube 7 in. [2-in. dia. Free air jet X30 30°

Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shown below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all friction. Air Open Water Stagnation Fixed vane tube 7 in. [2-in. dia. Free air jet X30 30°

Name: Problem 5.2.28 of Gehart, et al. (Problem 66, 7th ed.)Air discharges
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Problem 5.2.28 of Gehart, et al. (Problem 66, 7th ed.)Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shownbelow. A stagnation tube connected to a water U-tube manometer is located in the free

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 6.66 PLUS This nozzle bends the flow from vertically upward to 30° with the horizontal and…

A: Step 1:

Q: For the sprinkler shown, find a. the torque required to hold it steady, and b. the rotation rate in…

Q: Required information A jet of alcohol strikes the vertical plate as shown in figure. A force of 750N…

Q: Flow direction 581 N 759 N 625 N 874 N 811 N 679 N 723 N

A: Given data m˙ = 30 kg/s mass of water in elbow = 50 kg D = 13 cm d = 6 cm θ = 45o β = 1.03 To…

Q: Consider a reducer with inlet and outlet diameters of D1 and D2, respectively. The respective…

A: Law of conservation of momentum: According to this law, " the rate of change of linear momentum of…

Q: In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target…

Q: Problem 1. Air flows steadily in a duct from Section (1) to Section (2). At Section (1), the…

Q: Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal…

Q: A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and…

A: In order to solve the following problem, we must take some assumptions into consideration. The flow…

Q: 2. Three smooth rubber-lined fire hose each 60 m long and having 22 mm nozzle, are connected to a…

Q: A static pressure gauge and mercury manometer are connected to a 50.8 cm diameter pipeline flowing…

A: Given data: d=50.8 cmwHg=0.1336 N/cm3=133600 N/m3 Need to determine the velocity of the flowing…

Q: Consider the pipe shown in the figure below. The nozzle's center line is 0.3 m above the flange…

Q: A straight horizontal pipe 100 mm in diameter terminates in a short, tapering nozzle from which a…

Topic Video

Question

Problem 5.2.28 of Gehart, et al. (Problem 66, 7th ed.)
Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shown
below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the
horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all
friction.
Air
Open
Water-
Stagnation
tube
7 in.
r Fixed vane
12-in. dia.
Free
air jet
30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data.

VIEW

Step 2: Calculate the horizontal component of the force that the air jet exerts on vane.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The manometric head developed by a three-stage centrifugal pump runningat 450 rpm is 60 m. The width and diameter of each impeller at the outlet are60 mm and 750 mm, respectively, with outlet blade angle 45°. Determine itsmanometric efficiency, if discharge through the pump is 0.3 m^3/s.
An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per second. At the same time, receiving a fluid at a rate of 225 US Gal per minute. At a certain post the tank is considered to be quarter full. Find the (a) water level and the (b) mass change In the tank 15 minutes later. Given: tank diameter = 10 ft tank height = 20 ft
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
Problem 5.32: (Munson, et al. 5th ed.) Determine the magnitude and direction of the anchoring force needed to hold the horizontal elbow and nozzle combination show in place. At section (2), water discharges into the atmospheric at 100 kPa and the pressure at location (1) is 100 kPa gauge. 160 mm V₂ Section (2)1 V₁ 300 mm Water Section (1) P₁ = 100 kPa V₁ = 2 m/s X
Q1. What would be the effect on the calculated force on the flat plate if the jet were to leave the plate not horizontal but inclined upwards at an angle of 1 °? If the experiment were to be repeated with the vane in the form of a cone with an included angle of 60° (half angle 30°), how would you expect the results to appear?
Consider a pressure washer exerting a horizontal force on the wall (and the operator). Assume that water enters the pressure washer wand vertically. Output nozzle is 1/8" (0.125 inches) in diameter. A. What is the water pressure at the exit (once water leaves the nozzle)? b. Calculate the flow needed to produce 20lb of horizontal force.
contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P. 100 kPa water is 999 kg/m' and characteristic gas constant for V-0 air is 287 J/kg K. 25°C, O Test section 25°C (GATE) To manometer Fig. 6.6
A centrifugal fan with backward curved blades has an impeller overall diameter of 320mm and rotates at 1500r/min. The radial air velocity is 10m/s and the blade outlet angle is 35°. Calculate the theoretical pressure delivered by the fan if air of density 1.23kg/m cubid is handled
Vanes 6.20 Determine the external reactions in the x- and y-directions needed to hold this fixed vane, which turns the oil jet in a horizontal plane. Here V, is 18 m/s, V, = 17 m/s, and Q = 0.15 m /s.