Water flow passes under the sluice gate. Suppose that y₁ = 6 m and y2 = 1.9 m. (Figure 1) Figure Y₁ 4 m < 1 of 1 Part B Determine the critical depth of the flow downstream from the gate. Express your answer to three significant figures and include the appropriate units. Ye= 3.095 m Submit Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining

Water flow passes under the sluice gate. Suppose that y₁ = 6 m and y2 = 1.9 m. (Figure 1) Figure Y₁ 4 m < 1 of 1 Part B Determine the critical depth of the flow downstream from the gate. Express your answer to three significant figures and include the appropriate units. Ye= 3.095 m Submit Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: Kindly provide a solution pls. The answer is already provided. Thank you! A horizontal cylindrical tank with diameter 0.61 m. and 3.44 m. long is filled with water to a depth of 0.45 m. Find the depth (in meters) of the water if the tank is in its upright position. Round off to three decimal places.
The velocities recorded by current meter in a stream are given below. Find the discharge per unit width of stream near the point of measurement. Take the depth of flow at the point as 5m. Note : For Detail See Figure Attached . Please Provide Solution In Detail ASAP.
Question 9. (Problem 11.39, Engineering Fluid Mechanics by Elger et al.) Estimatethe depth of water before and after the jump for the hydraulic jump downstream of the sluice gate. yi = 1.5 m > Vị = 0.2 m/s
pls answer in 3 decimal places. subject: hydraulics engineering
The following are the data obtained in a stream gauging operation. A current meter with a calibration equation V = (0.32 N + 0.032) m/sec was used to measure the velocity at 0.6 depth. Using the mid-section method, calculate the discharge in stream. Distance from the right bank Depth 0 2 4 6 9 12 15 18 20 22 23 24 0 0.5 1.10 1.95 2.25 1.85 1.75 1.65 1.50 1.25 0.75 0 No. of revolutions 0 80 83 131 139 121 114 109 92 85 70 0 Time (Sec) 0 180 120 120 120 120 120 120 120 120 150 0
64 Q. No 2). A pipe line is designed to supplying water with flowrate of X 1/s to fulfil the demand and consumption of a city. Determine the head loss and velocity of flow in 1500 m long water supply line section having diameter of Y cm. Assuming coefficient of friction factor f=0.00155. 19.2 lowrate) and Y (Diameter) from following table
Water flows through a Venturi meter as shown below. Determine the discharge coefficient, Cd, of the Venturi meter if the actual discharge is determined to be 2.19 cfs. Use D1 = 12.46 in., D2 = 4.29 in., y = 8.28 in. Points 1 and 2 are centerlines of the inlet and throat, respectively. Round off to five decimal places. Water 2 Di Da Mercury
B. Water flows in a tapering pipe vertically as shown in Fig. 2. Determine the manometer reading 'h'. The flow rate is 100 litter s, take SG mercury = 13.6, and y=9810 N/m Fig. 2 06m d2= 01m Water dia 02m 2 h Mercury
A 2-ft-diameter unfinished-concrete drain pipe has been designed to transport 90 ft³/s of water at a depth of 1.5 ft. Part A Determine the required downward slope of the pipe. Express your answer using three significant figures. — ΑΣΦ ↓↑ vec So = Submit Request Answer
Pipe with L=2km, HL (head loss)=96.68m and roughness Ks=0.046mm has flowing water with viscosity v=1*10^-6 (m2/sec). D=75mm. Find the average velocity from Moody Chart. (Handwritten solution)
Question 03: Consider a flow field represented by the stream function w = (4+27) x'y - (6+27) x'y? + (4+27) xy'. Is this a possible two-dimensional incompressible flow? Is the flow irrotational? Discuss the reasons against your findings.