Water at 45°C flows through a 205 m 2" Schedule 40 steel pipe. The available head of the H2O is 5m. Assume there are no head losses in the valves and fittings, find the mass flow and volumetric rate of water.

Q: 1.A liquid refrigerant (sg = 1.080) is flowing at a weight flow rate of 23.0 N/h. Required…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: asoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure…

A: Givenh2=52.8ftTemp=77°Fρgasoline=45lb/ft3

Q: Compute the resulting pressure in kPa after a "real" diffuser in which the energy loss due to sudden…

A:

Q: Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K…

A: Given: The diameter of the pipe, d = 3/4 in The volume flow rate, Q = 0.5 gal/min The temperature of…

Q: In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve…

A: Given that, K1=0.5K2=6Flow rate of water, Q=0.015 m3/sec,Density of water, ρ=1000 kg/m3Friction…

Q: Air moves through a tube that has a radius of 0.6 cm. If conditions are at STP, find the critical…

A:

Q: The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is…

A: Note: As per the policy, we can solve the first three subparts. Please resubmit the remaining part.…

Q: 8.29 Air at 70°C and atmospheric pressure flows with a velocity of 22 fps through a 3-in-diameter…

A:

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa    dA=150mm PB=325KPa    dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: 34. A pressurized tank contains saturated water. A frictionless valve on the pipe is now opened to…

A: Given Data:Note:

Q: 1) With the below nozzle arrangement, what pressure is needed in the pipe in order to get a nozzle…

A: From the given data,

Q: Convert 50 GPM to ft/s in a 4" Sch 40 pipe

A: Given data: V˙=50 GPMPipe=4'' schedule 40 pipe Need to Convert 50 GPM to ft/s.

Q: Assuming a permanent loss using the pressure drop from the 180 L/min flow rate and taking energy to…

A: Flow rate ,Q = 180 L/min or 0.003 m3/s Time = 24 hours

Q: Oil at 24 gpm and 1200 psi enters the low-pressure inlet of a 4:1 Racine pressure intensifier. Find…

A: Introduction: The Racine pressure intensifier is used to boost the oil or air exit pressure. It…

Q: mass flow rate. 6.31 A liquid refrigerant (sg 1.08) is flowing at a weight flow rate of 28 3 N/h.…

A: First we have calculated the value of density of refrigerant, density of refrigerant is equal to…

Q: Consider a positive displacement pump; Shaft speed is 1800rpm Pump push 0.003gal/revolution Leakage…

A:

Q: Water at 68 deg F is flowing at a rate of 25 gal/min through a pipe that is made of 1-inch sched 40…

A:

Q: Ethylene glycol at 10C is flowing in a 10 cm internal diameter copper tube at 0.95m /s Find the…

A:

Q: A pipe with a diameter of 2cm is attached to a garden hose with a nozzle. If the velocity of flow in…

A: Givenpipe diameter d=2cm=0.02mVelocity in the pipe V=2m/swhen d'=4mm=0.004m

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.