Water at 20°C flows over a flat plate at 12 m/s. At a 4 m compute the following:a. The viscous wall layer thickness. S, =ст.b. The velocity at the edge of the viscous wall layer. V =m/s.c. The boundary layer of thickness. 8 =ст.

Answered: Image /qna-images/answer/372330c6-6c07-4c4c-bb30-c3a1b81039ed.jpg

Water at 20°C flows over a flat plate at 12 m/s. At a 4 m compute the following: a. The viscous wall layer thickness. &, = ст. b. The velocity at the edge of the viscous wall layer. V= m/s. c. The boundary layer of thickness. & = ст.

Water at 20°C flows over a flat plate at 12 m/s. At a 4 m compute the following: a. The viscous wall layer thickness. &, = ст. b. The velocity at the edge of the viscous wall layer. V= m/s. c. The boundary layer of thickness. & = ст.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

27. Engine of an airplane (v =102.5 m-s", V2 = 792 m-s", Ftn = 31.8 kN, A, = 2.88 A2, p1 = 1.26 P2, P2 = 102.3 kPa, A2 0.58 m?), calculate the inlet density.
(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of Vwinarunnet = 50 m/s. The measured downforce at this speed is Foownforce.WT = 3000 N and the model reference area is Aref wT = 0.5 m?. 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p = 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g = 9.81 m/s?. Downforce Weight
b) A group of engineers is planning to built a tunnel going through a mountain range for vehicle to pass through. Assume the built tunnel has a diameter of 15m, wind (air) at 20 °C and 20m/s is flowing across the tunnel with p = 1.204 kg/m³ and μ = 1.825 x 10-5kg/ms. The width of the approaching vehicle is given to be 2.5m. Implementing the dimensionless parameters obtain in (a), determine the speed of air and the width of body if the experimental work is to be run in a wind tunnel with a diameter of 5m at 25 °C (p = 1.184 kg/m³ and μ = 1.849 x 10-5kg/ms.)
Fluid 10
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
1. Consider a flow with the velocity profile shown in the image below. Here, U is called the freestream velocity and & is called the boundary layer thickness. Calculate the shear stress acting on the fluid surface if the freestream velocity is 10 m/s, the boundary layer thickness is 2 mm, and the fluid's dynamic viscosity 10.³ Pa.s. fluid surface U.. 8
i need clear ans by hand and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
i need the answer quickly