Water at 100ºF is flowing through a long, straight, 4-in schedule 40 steel pipe at a rate of 6.2 gal/min. What is the velocity at the center of the pipe?

Q: A garden hose attached with a nozzle is used to fill a 10-gal bucket. The inner diameter of the hose…

A: Volume of bucket = 10 gal 1 gal = 3.789 × 10-3 so volume of bucket = 3.789 × 10-2 m3 Initial…

Q: Water with density 1000 kg/m3 flow in a 4-in ID pipe at 1,2 m/s, witch connect to a Venturi meter to…

A: Density of water = 1000Inner diameter of pipe = 4 in.Water velocity at the inlet of pipe = 1.2…

Q: K()" where K=0.05 Pa.sº.. It A non-Newtonian fluid is modelled by the equation of r = K ( flows…

A: Given, Diameter of pipe = 6 mm i.e R = 0.003 m

Q: Q6: Water flows under the inclined sluice gate shown in Fig. P3.6.103. Determine the flowrate if the…

A: Flowrate of the water is asked.

Q: Water is flowing through a 2.067-in ID pipe with a velocity of 1 m/s. Calculate: (a) Mass flowrate…

A: Density is the ratio of mass by volume. The mass flow rate is the ratio of unit mass per unit time.…

Q: 10 ft 10 ft Very large Water 3-in steel pipe FIGURE 6.25 Tank draining by gravity, with pipe and…

A: Water is flowing from the bottom of a tank via 3 in steel pipe. Volumetric flow rate is to be…

Q: 2. Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow…

A: to determine whether flow is laminar or tarbulent we use reynold number  NRe=ρvdμhere ρ is densityv…

Q: Water enters a 5cm diameter piping system from a reservoir with volumetric flow rate of 50cm3/s.…

A: Given that diameter ,d = 5 cm =0.05 mVolumetric flow rate,Q = 50 cm3 /sviscosity of water during…

Q: 7 ft 1.5 ft SAMPLE PROBLEM 2.6 As part of the design of a new sailboat, it is desired to determine…

A: It is asked to determine the drag force exerted on the hull and the tension of cable AC.

Q: Water is pumped at 1.4 m/s from a tank at a treatment plant to a tank at a local works through two…

A: Volumetric flow rateQ=1.4m3/sd1=0.3md2=0.6mAssume: turbulent flow, pressure drop is same.To find:1.…

Q: When liquid and vapour phases of one component system are in equilibrium (at a given temperature and…

A: The molar free energy in the liquid and vapor phases of a one-component system is equal when the…

Q: he below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oil tanker…

A:

Q: Water flows steadily from a large pressurized closed tank as shown. The pressure difference measured…

A: head developed by manometer(h)=xρmρl-1 where, x-deflection of manometric fluid=1 inch ρm- density of…

Q: 5.30. The venturi meter in Fig. 5.30 has air flowing through it. The manometer, as shown, contains…

A: It is given that air is flowing in the venturi meter. Given data are as follows: Inlet area of…

Q: 2.3 A 12mm diameter pipe 15m length is used to drain an oil tank. Determine the discharge when the…

A: given data:diameter=12mm=0.012mlength=5moil level in the tank 2m aboveh=2moil viscosityμ=0.01 pu…

Q: (d) Increasin 02 A Semi-circular gate of radius 1m is placed at the bottom of a water reservoir as…

A: This question is based on fluid mechanics. Let us see what data are given:  Radius of the semi…

Q: Problem 5. Fluid (r = 56 lbm/ft®) enters a pipe bend of constant 5 in. diameter with velocity of 20…

A: Density of the fluid, ρ = 56 lbm/ft3 Diameter of the bend pipe, d = 5 in. Velocity of the fluid at…

Q: Figure 5 shows a conical vessel having its outlet at A to which a U tube manometer is connected. The…

A: Initial difference in the height of the mercury level,h2=20 cm=20100=0.2 m Diameter of the conical…

Q: If d (diameter )is 50. . m, u ( typical speed) 70 m/s, and u (speed) id 90 m/s then Re .a…

A:

Q: For the setup shown in Fig. P2.33, find the differ- ence in pressure between the oil pipe and the…

A:

Q: 2.10-2. Frictional Pressure Drop in Flow of Olive Oil. Calculate the frictional pressure drop in…

A: Given: T = 293 K Inside diameter d = 0.0525 m Length L = 76.2 m Velocity v = 1.22 m/sec Required:…

Q: Water is flowing through a rectangular duct (width = 0.75m height = 1.3 %3D m) of standard steel.…

A: Assume the flow to be laminar in nature. The duct hydraulic diameter is obtained by width and…