W A reinforced concrete T-beam with d = 550 mm, b = 300 mm, slab thickness=100 mm is 4.8 m long and spaced 3 m on centers. The beam support a service dead load moment of 400 kN.m (including its weight) and service live load moment of 500 kN.m. If fc'=27.5 MPa, fy = 414 MPa, determine the required steel area.

W A reinforced concrete T-beam with d = 550 mm, b = 300 mm, slab thickness=100 mm is 4.8 m long and spaced 3 m on centers. The beam support a service dead load moment of 400 kN.m (including its weight) and service live load moment of 500 kN.m. If fc'=27.5 MPa, fy = 414 MPa, determine the required steel area.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer to the question in reinforced concrete
A T beam has a concrete and steel strengths of 28 MPa and 420 MPa. The live load is 3830 Pa. while the dead load in addition to concrete's weight is to be 4097. The density of concrete is 2400 kg/m³. The slab is 125 mm thick while the effective depth is 600 mm, the total height of T-beam of 675 mm and the bottom width of T beam is 375 mm. The length of the beam is 7 meters. The center-to-center spacing of beams is 330 cm. Determine the arrangement of main reinforcement bars. Check for clear spacing.
1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.
A reinforced concrete beam has a width of 250mm and an effective depth of 500mm. If F'c= 28MPa, Fy = 415MPa, determine the following: a. Maximum steel area for singly reinforced condition. b. Maximum design strength if the beam is singly reinforced. c. The required steel area if the beam is subjected to a dead load moment of 100KN.m and live load moment of 130KN.m.
A concrete beam of length 5.5m is built monolithically with the slab. Originally, the beam has a width of 300mm and effective depth of 400mm. If the flange of the slab is 150mm and the total area tension steel bars is 500 sq.cm., determine the design capacity of the beam structure. The concrete has a compressive strength of 25 MPa, steels' yield strength is 420 MPa. and the beam's clear span from its adjacent beams is 2.15m.
The simply supported I-beam shown in cross-section and elevation is to carry a uniform service live load totalling 8 kN/m over 12m span, in addition to its own weight. The beam will be pretensioned using multiple seven-wire strands, eccentricity is 130mm and constant. The 28-day compressive strength of concrete is 40 Mpa. Calculate deflections
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
Situation 3: A6 m long fix-ended concrete beam has a width of 310 mm and an overall depth of 480 mm. The beam is reinforced with 4-28 mm diameter bars at the bottom and 2-28 mm bars on top. Steel cover measure from the center of the bar is 70 mm. f'e- 28 Mpa and fy-415 Mpa. Total dead load including beam weight is 22 kN/m. Assuming the analysis is Doubly-reinforced beam. 7. Determine the depth of compression block in mm. 8. Determine design ultimate moment of the section if reduction factor is 0.90. 9. Determine the additional concentrated live load can carry at the midspan.
A rectangular beam has b = 350 mm and d = 460 mm.the concrete compression strength is 30 MPa and the steelyield strength fy = 415 MPa. Calculate the required steelreinforcement area if the steel cover is 70 mm.use NSCP 2010 Md = 230 KN-mML = 160 KN-m
reinforced Concrete
Reinforced Concrete
A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 279MPa. The depth of the concrete stress block is ___ mm.