Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must belimited to 185 MPa, determine the minimum diameter required for each rod. Assume P = 79 kN and Q = 134 kN.%3DdzdiBAnswers:d1 =mm.d2 =mm.

Answered: Image /qna-images/answer/e237de70-6ebe-4ad3-8349-d7968e0b7808.jpg

vo solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be hited to 185 MPa, determine the minimum diameter required for each rod. Assume P = 79 kN and Q = 134 kN. dz (2) B

vo solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be hited to 185 MPa, determine the minimum diameter required for each rod. Assume P = 79 kN and Q = 134 kN. dz (2) B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1320 mm². Assume a = 2.4 m, b = 9.7 m, and c = 3.6 m. If P = 60 kN and Q = 70 kN, determine the normal stress in each member. a Answers: OAB = i MPa (C) MPa (Т) i MPa (Т)
Problem 1A steel wire is 6 m long, hanging vertically supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4mm. E = 200, 000 MPa.
The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
The frame is loaded by a distributed load of intensity q as shown. Consider -25 in. only stress in the bars AC and BC. Each bar has a cross-section that is 0.75 in by 1.5 in. If the allowable normal stress is 5000 psi, determine the maximum allowable value for the distributed load intensity q. 40 in.
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 14 mm2. For a uniformly distributed load of w = 4.1 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.35 m. A (1) (2) a L. Answer: a = i m
The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load Pis applied. Assume a = 4 and b = 5. Determine (a) the magnitude of load P. (b) the shear stress on plane AB. (c) the maximum normal and shear stresses in the block at any possible orientation. P B Answers: (а) Р- i kips (b) Tự = i ksi (c) Omax = i ksi Tmax i ksi
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
The steel bar shown has a 100 mm by 25 mm rectangular cross section. If an axial force of P = 180 kN is applied to the bar, determine the maximum normal stress (in MPa) acting in the bar. Note: Your submitted answer should not include units. 100 mm Answer:
The five-bolt connection shown must support an applied load of P = 235 kN. If the average shear stress in the bolts must be limited to 195 MPa, determine the minimum bolt diameter that may be used in the connection. Answer:d = i mm.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e� = 55 mmmm and is subjected to the loading shown. Let a� = 200 mmmm , b� = 220 mmmm , c� = 350 mmmm , d� = 250 mmmm , and P� = 3.0 kNkN . Take point A to be at the top of the circular cross-section. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, Mx��. b) Part B - Moment about the z axis at A Part C - Stress due to the normal force To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the normal force. Part D - Stress due to the bending moment about the x axis To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the bending moment about the x axis.
Two axial members are used to 4.3 m support a load P applied at joint B. Member (1) has a cross-sectional area of A: = 3,080 mm? and an allowable normal stress of 180 MPa. Member (2) has a cross-sectional area of A2 = 4,650 mm? and an (1) 5.0 m allowable normal stress of 75 MPa. Determine the maximum load P that may be supported by the structure without exceeding either allowable normal stress. (2) 2.0 m