vị(t)u(t) + R L eeeee C + vo(t) See the dynamic RLC circuit shown above. It has a time dependent input of vi(t)u(t). A. Redraw the CCT in the s-domain labeling polarities, current directions, and circuit variables. Assume zero initial conditions and label nodes if node voltage analysis is used. B. Derive the transfer function, T(s), from Vi(s) to Vo(s) by combining and reducing the rightmost parallel inductor and capacitor branches into an equivalent impedance. (Hint: create series circuit and use voltage division) Help on part C: C. At the output interface, derive the Thévenin equivalent voltage, VT (s) using the transfer function. Then use the lookback method to derive the Thévenin equivalent impedance, ZT (s), at the output.

vị(t)u(t) + R L eeeee C + vo(t) See the dynamic RLC circuit shown above. It has a time dependent input of vi(t)u(t). A. Redraw the CCT in the s-domain labeling polarities, current directions, and circuit variables. Assume zero initial conditions and label nodes if node voltage analysis is used. B. Derive the transfer function, T(s), from Vi(s) to Vo(s) by combining and reducing the rightmost parallel inductor and capacitor branches into an equivalent impedance. (Hint: create series circuit and use voltage division) Help on part C: C. At the output interface, derive the Thévenin equivalent voltage, VT (s) using the transfer function. Then use the lookback method to derive the Thévenin equivalent impedance, ZT (s), at the output.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A position control is to be designed with a 20% overshoot and a settling time of 2 seconds. The components which composed the system are: An amplifier and a power amplifier to drive the motor, whose cascaded transfer function is K₁/(s+20). ● Two pots are available to convert shaft position into voltage; the transfer function is 1/2. A dc motor whose transfer function is 20/s(s+2). a. Draw a complete block diagram of the system, specifying the transfer function of each component when the system is operating with 20% overshoot. b. What will the steady-state error be for a unit ramp input? c. Determine the transient response characteristics.
b) The unit step response of a first order system is shown below: Develop the transfer function of this system. Please include detailed steps. Hint: Please find the time constant and the constant gain (the numerator).
Electrical Engineering Write the equations for small-signal ac dynamic model of buck-converier and defive the following iL(s) (ii) Din(s)lāt)=0 Do(s)| transfer functions, (i) a(s) Din(t)=0
R(s) G₁(s) G₂(s) G4(S) G6(s) G3(s) G5(s) - H₁(s) G7(s) b) Find the equivalent transfer function of this system. -H₂(s) C(s) - H3(s) a) Convert the signal flow graph into an equivalent block diagram, no simplification needed
The filtering stage of a biomedical device passes signals with frequencies ranging between 20Hz and 500Hz while the stage delivers a total gain of 48.Design the electronic circuit of the filtering stage using appropriate numbers ofoperational amplifiers, resistors, and capacitors.N.B.: The filters are all 1st order active filters and the maximum possible gain is limited to 10for a single amplifier.
S:37)
Q.1) Given the block diagram of a system shown in Figure below, find: 1. Convert the block diagram to a signal-flow graph. 2. Find the transfer function via signal-flow graph. G8(s) C(s) R(s) G1(s) Gs(s) G6(s) G2(s) G4(s) G7(3) G3(s)
Step by step
L Exercise. You can write the DC motor angular velocity transfer function as s + bs +c (a) Suppose that a DC motor has constants g = 60, b = 2.3, and e = 11. Define the transfer function in MATLAB using the tf function. % write your code here (b) Is the system stable? You can plot the poles in the s-plane using the pzmap function. For example, to plot the poles of a transfer function G, use: pznap(G) % write your code here (c) What are the poles of the transfer function? You can use the pole function to compute the poles of a dynamic system in MATLAB. For example, to identify the poles of a transfer function R, use: pole(R) % write your code here
determine transfer function for 2nd order RC lpf in the same way stated in the book
20 3. For the open loop transfer function G(s) = (s+3) a. Sketch the original closed loop step response b. Design a PI controller that will optimize the response c. Sketch the final closed loop step response
I’d appreciate a fast response