A closed system undergoes a thermodynamic cycle with three steps: process 1-2 (from state 1 to state 2), process 2-3 (from state 2 to state 3), process 3-1 (from state 3 to state 1).During process 1-2, the system received energy by heat transfer of 5J and did work of 10J.During process 2-3, the system was transferred energy from its surrounding by heat transfer of 25J and work was done on the system of 20J.During process 3-1, the system discharged 40J to its surrounding by heat transfer.What are Qin and Qout in this cycle?Enter the answers separate by / and without units and spaces. For example, 27/13.

Answered: Image /qna-images/answer/62e60311-7889-4da6-8f3e-eff3ed6fccab.jpg

Answered: Vhat are Qin and Qout in this cycle?

Engineering

Mechanical Engineering

Vhat are Qin and Qout in this cycle?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure shows reversible cycle. Determine Work output from the engine.
What’s the answer for this please ?
Give neat solution in text.
please dumb this down for me
In an ideal Diesel Cycle, the temperature of the air at the beginning of compression is 320 K and the pressure is 100 kPa. The maximum temperature of this cycle with isotropic compression ratio of 15 ; A-)2500K B-)2000K Find the temperatures and pressures that are not given according to the situation, the heat given for 1kg of air, the net work and the average effective pressure. Draw the diagrams P-v and T-S.
quickly solve with me time 30 minutes...In an ideal Bryton cycle gas turbine unit, air is drawn in at (1.02 bar and 15 C°), and is compressed to (6.12 bar). Calculate the thermal efficiency and the work ratio of this ideal cycle, when the maximum cycle temperature is limited to (800 C°).
A two stroke spark ignition engine is running at 2000 rpm, compute the time (in milli second) for completion of one thermodynamical cycle for this engine.
Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
3. A CARNOT ENGINE PRODUCES 30 kW WHILE OPERAING BEWCAN TEMPERATURE LIMITS OF T50°C AND 200 °C PETER MINU A) THE SRNTROPIC XPANSION RATIO 8) THE HEATSUPPIED PER SE COND C:) THe HEAT FEJELION PER SECOND D.) THE THEAMAL EFFICIUNCY OF THE CYCLE
yale L 15 A gas power cycle uses air as the working fluid and has two turbine sections as shown in the figare below. The power produced by Turbine I is used to drive the compressor, and Turbine 2 produces output power W. Air enters the compressor with a semperature of 290 K and a mass flow rate of -2 (kgs] (State I); the air exits the compressor at 44SK (State 2). Heat is transferred from a high- temperature thermal reservoir, Ta- 1400 [K), to Heat Exchanger 1 at a rate Q,- The lemperature of the air is raised to 1100 [K] (State 3) as it flows through Heat Exchanger 1. The air enters Turbine I where it is expanded to State 4. The flow then proceeds to Turbine 2 and exits with a temperature of 500 (K] (State 5). Heat is then removed from the air through Heat Exchanger 2 at a rate Q which is rejectod to the low-temperature thermal reservoir, TL-200 (K). (A) Determine the temperature at the inlet to Turbine 2, Te (b) Calculate the power output from Turbine 2, W. (e) Calculate the rate of…
i need the answer quickly
QUESTION I Figure 1 shows cylinder block and piston of a reciprocating engine run with diesel fuel. The engine has displacement volume of 3000 cm and has clearance volume. Consider that the engine is a four-cylinder and four-stroke operates on the Diesel cycle with a compression ratio of 18 and cutoff ratio of 2. The pressure and temperature of air is at the beginning of the compression process is dependent on local ambient condition. Using constant specific heats at 500 K: i) decide working condition at the beginning of the compression process and calculate all the working temperature and pressure at all points on P-V diagram for the engine, ii) determine the net work output and the thermal efficiency, iii) determine the mean effective pressure, iv) develop expression of Power (P) as a function of rotational speed (N), and v) plot graph of Power versus Engine speed (RPM) for the above engine from 0 – 4500 rpm. Please provide complete table of Power versus Engine speed. What is the…