Ncc18 VJIcRc91 KeREVBE1,1k2VoAイk2RB2-90BABIACalaulatethe value of the Reresis tance thatwill teep the collector voltage at 12 volts within theto groundCircurt in the Pigure.respectFERU(vBE = 0,7 V)0,7 v)%3D

Answered: Image /qna-images/answer/cbc67bdd-1f72-4926-8b47-06081ca4ae6e.jpg

VCC = 18 V %3D VIc Rc RE JBE 1,1k-2 RB2 BABIA resis tance hat 12 volts with 429MR Caloulate the value of the Re will teep the collector voltage to ground in the Circuit in the figure. respect (vBE = 0,7 V) %3D

VCC = 18 V %3D VIc Rc RE JBE 1,1k-2 RB2 BABIA resis tance hat 12 volts with 429MR Caloulate the value of the Re will teep the collector voltage to ground in the Circuit in the figure. respect (vBE = 0,7 V) %3D

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Npn with a β value of 100 in the circuit in the figurefor zener diodes used to drive the transistorGiven as VZ1=16.7 V and VZ2=5.6 V. Inanalysis of transistor operating point Circuitidentify by.(VBE=0.7 V )
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
What are the peak voltage values for both half cycles of the output waveform. V=35sin(wt). Use modified ideal diode model (Va=0.7V) for diodes. 5 k2 Z1 Vo Vi 20-V Zeners Z2 O34.30V, -34.30V O35.70V, -35.70V O 17.60V, -17.15V O35V, -35.00V OOv,oV Clear my choice
G2/.Design Circint as the following peseripton: A- the positive Cycle of the vout signal is 3.2 and Negative cycle is 4-33 (Note: we must used preetical Diodes and vin is lov) 13- the positive cyclep of vout is s.3 ond Negative cycle is (5.4) [Note:consider vin = tovavd we must used Capaetor with praeticul Didde)
For the diode circuit shown below, an IN4007 diode is used, and is connected to a variable voltage supply (VIN) that provides a maximum output voltage of 6 V. The 1N4007 diode has absolute maximum forward current rating of 1A, and can be modelled with a diode drop of 0.7 V. What is the minimum value of resistance (R1) you can use to avoid damage to the diode? Answer: Vin ww R1 O Vout
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…
I need help quickly please
What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph .