For the diode circuit shown below, an IN4007 diode is used, and is connected to a variable voltage supply (VIN) that provides a maximum output voltage of 6 V. The 1N4007 diode has absolute maximum forward current rating of 1A, and can be modelled with a diode drop of 0.7 V. What is the minimum value of resistance (R1) you can use to avoid damage to the diode? Answer: Vin ww1. R1 Vout

For the diode circuit shown below, an IN4007 diode is used, and is connected to a variable voltage supply (VIN) that provides a maximum output voltage of 6 V. The 1N4007 diode has absolute maximum forward current rating of 1A, and can be modelled with a diode drop of 0.7 V. What is the minimum value of resistance (R1) you can use to avoid damage to the diode? Answer: Vin ww1. R1 Vout

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Sketch the shape of the output voltage waveform for this clipper circuit, assuming an ideal diode with no forward voltage drop.
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Find out the unknown values providing correct solution in detail.Also find out if the assumption given in thq question is correct or wrong. Give a short explanationLet the ID = 9
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
Compared to an ideal PN diode, what are the different characteristics of a practical PN diode? Please list two different characteristics when the diode is reversed biased.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Answer all the questions one by one and solve all the unknown values with correct details
A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED