(V1) 7. A3 (4A) R1 R2 A1 = A1 A2 = A3 = A2 5V 3V) V1 = 30 V2= 20 R1 = R2 = V2

Q: crease roughly at the rate of 18 percent per year. Estimate the number of years that the army should…

A: Calculate the old replacement age  Cu= au Su = k-bu Calculate the total cost incurred in the cycle

Q: do fast.

A: First, we need to understand the problem. We are given a three-phase heating element with each phase…

Q: To send digital data over a digital circuit, it should be converted before transmission * True False…

A: Introduction: In general, the computer involves different layers for the message to get connected…

Q: A 50-lb ladder rests against a wall when the bottom begins to slide out. The ladder is 35-ft long…

A: Step 1: Step 2: Step 3: Step 4:

Q: Jose just found out that at his part-time job in the restaurant, the manager was replacing all of…

A: McDonaldization at a workplace would include,  Efficiency Calculability Predictability and  Control

Q: An efficient system can be ineffective and vice versa. Select one: a. True b. False

A: An efficient system can be ineffective and vice versa that statement is :

Q: At Naoki's Jewelry Store, there are fine jewels, expert employees, and modern security features.…

A: Operations management is a vast concept that not only includes inventory and production-related…

Q: do fast correct answer step by step

A: Step 1: Step 2: Step 3: Step 4:

Q: which of these is not true about DMADV    options are  Addresses the to-be process  Reduces/…

A: DMADV is nothing but the acronym for Define, Measure, Analyze, Design, and Verify. DMADV is…

Q: A wheel tractor-scraper is carrying a 50,000 lb load while operating on a level grade. Assume no…

A: Introduction: The term Market refers to an exchange of goods and services between the buyer and the…

Q: What mechanical element is analogous to electrical resistance in an equivalent circuit?a) Mass b)…

A: The question is asking for the mechanical element that is analogous to electrical resistance in an…

Q: Assume that a system is composed of two independent and identical units in parallel and at least one…

A: The detailed solution is given in Step 2.

Q: A stream of oxygen enters a compressor at 25 \deg C and 1 bar with an inlet volumetric flow of 1.3…

A: Step 1:To determine the power required by the compressor, the speed of entropy generation, and the…

Q: A LVDT type displacement transducer with a primary of 300 turns and secondary of 500 turns in each…

A:

Q: The total time rate of change of the moment of momentum for the contents of a control volume is…

A: The question is asking about the total time rate of change of the moment of momentum for the…

Q: What is the effect of a clamping circuit on the AC component of a signal?  - A) Inverts the AC…

A: A clamping circuit or clamper is an electronic circuit that prevents a signal from exceeding a…

Q: What is the purpose of biasing a transistor?   A) To set the transistor's operating point B) To…

A: In electronics, biasing is a method of establishing predetermined voltages and/or currents at…

Q: Don't use chatgpt.....

A: Given that the primary voltage of the transformer is VP​=240 VoltThe turns ratio is n=1:4  or…

Q: . An 18 V source has an internal resistance of 70. If a load resistance of 33 is connected to the…

A: The objective of the question is to find the power dissipated across the load resistance when it is…

Q: Given a transfer function (first order-assume any) and unit impulse. Explain the influence of…

A: The transfer function of a control system is defined as the ratio of the Laplace transform of the…

Q: do fast

A: Given peak value of sine function (Vpeak) = 20 VThe formula for sine function with the phase angle…

Q: Tolerance is the allowable amount of error above and below an ideal measurement. In a manufacturing…

A: A detergent carton claimable amount = 1.5 kg Tolerance limit = 0.005 kg per box Amount claimed to be…

Q: Markland First National Bank of Rolla utilizes kanban techniques in its check processing facility.…

A: Given, container hold =25 checks and spend 24 min a day material handling = 2hrs a day facility…

Q: Design an electric vehicle gear reduction system that can accelerate from 0 to 100 km/h in less…

A: Step 1: Step 2: Step 3: Step 4:

Q: What happens to the operating point of a transistor if the temperature increases?      - A) Shifts…

A: The operating point of a transistor, also known as the quiescent point (Q-point), is the DC…

Q: A tool and die press that stamps out cans used in a small gasoline engine tends to break down once…

A: This is a special case of queuing. Maintenance is a necessary part conducted by the manufacturing…

Q: The availability of a system is affected when the mean time between failures (MTTR) is approaching…

A: Mean Time Between Failures (MTBF) helps to specifies  how long a new system and repaired  system…

Q: When many computers on the same circuit send data at the same time, this may cause a(n): *…

A: Here, question has asked about the situation when many computers on the same circuit send data at…

Q: The data capacity of a circuit is measured in terms of the number of bits per second (bps) * O True

A: The data capcity refers to the data amount that can be kept in the tag. With the higher data…

Q: A small turbine delivers 150kW and is supplied with steam at 700°C, 2MPa. The exhaust passes through…

A:

Q: Functions individually performing "best in class" combine to achieve the lowest total cost or…

A: Functions individually performing "best in class" combine to achieve the lowest total cost or…

Q: For data design for systems we often use 3rd normal form.  discuss third normal form.  What is it?…

A: The third normal form 3nf can be defined as the database design approach for the relational database…

Q: The co-founders of a startup are evaluating two alternative lean canvasses under consideration for…

A: As they are going to start a new business so, initially they should focus on acquiring more and more…

Q: An item has constant failure rate = 0.0005 per hour. When the item fails, it is repaired to an “as…

A: Given: λ=0.0005 per hourMean Time to Repair(MTTR)=6 hours Therefore, Mean Time to Fail is calculated…

Q: There are 3 main error detection techniques: parity checking, data checking, and cyclic redundancy…

A: This is true/false question, question has stated that there are three main error detection…

Q: Design process is non cyclical. Select one: O True O.False

A: Non cyclic process means the process which is irreversible or once a decision is made cannot be…

Q: a. If there are 29 kanban containers in use, the current daily demand of the check processing…

A: Given: Average demand d 6000 Average waiting time per unit w 0.083 Average processing time…