do fast current answer all 1. A simply supported circular shaft shown in Figure 1 is made from hot rolled 1040steel. AC=500mm, BC=1000mm. Diameter of the shaft is 10 mm for AC, 15mm forBC and has a fillet of radius 3 mm at C and 2 mm at B. It carries a gear at point C ofdiameter 200 mm and pressure angle of 20° and transmits a constant power of 1kWat 3000 rpm.(a) Determine the stress state on the critical element.(b) Determine the factor of safety using Goodman criteria.(c) Check for first cycle yield.(d) Determine the cycles to failure if not designed for infinite life.A> ☑CFigure 1B

## Analyzing the Shaft Design**Problem Statement:**A simply supported circular shaft is subjected to…

Answered: 1. A simply supported circular shaft…

Understanding Business

12th Edition

ISBN:9781259929434

Author:William Nickels

Publisher:William Nickels

Chapter1: Taking Risks And Making Profits Within The Dynamic Business Environment

Section: Chapter Questions

Problem 1CE

See similar textbooks

Similar questions

THE ARMATURE CONDUCTORS, 65% OF A DC Motok OF WHICH ARE DIRECTLY FLUX HAS 648 DENSITY IS UNDER THE POLE WHERE LINES PER SQ. 48,000 IN. IF THE CORE DIAMETER IS 7 INCHES AMD ITS LENGTA 1 4". THE CURRENT FOLLOWING THROUGH CONDUCTOR IS 20 A. CALCULATE : THE a.) THE TOTAL FORCE ARMATURE. b) THE TORQUE LB. FT. TENDING TO ROTATE THE EXERTED BY THE ARMATURE IN
Motiyo
No chatgpt used i will give 5 upvotes typing please i need all answers
do fast step by step
A ring of radius ' 6m ' placed on the y - z plane with its center in located at the origin, carrying a current of 5A. Determine the field point's location along the ring's axig to have a magnetic field intensity of - 90aₓ mA/m.
A 10-inch industrial fire hydrant has a 6-inch diameter fire hose with a 0.77-inch nozzle that discharges a water jet into the air on the right end. The pressure in the hose is 60 psi and the flow rate is 2,236 GPM. What is the resultant axial force (net value only) the water exerts on the nozzle, in pounds? 6-in. Oa. 6,873 pounds Ob. 8,473 pounds Oc. 10,854 pounds Od. 12,926 pounds
A Brayton Cycle operates with two stage compression with intercooling back to Ti. The pressure ratio across each stage 4. Air enters the cycle at a pressure of 14 psia and temperature of 100°F. The maximum temperature of the cycle is 1690 °F. The isentropic efficiencies of the compressors and turbine are 0.90. Assume temperature dependent properties (Table A-22 E). a). Draw the T-s diagram b). Determine the back work ratio c)Determine the thermal efficiency of the cycle. don't use handwritten diagaram
A journal bearing is 2.5in. long and has a shaft diameter of 1.25in. If the bearing characteristic number is found to be 1.4, find the minimum film thickness.
FJ Corporation’s electronic chip production process yields with an average life of 1,800 hours and = 100 hours. The upper and lower specification limits are 2,400 hours and 1,600 hours respectively. Is this process capable of producing electronic chips to specification?
do fast 100 upvotes.
Known: syrup (cv = 2700 J/kg K), density = 1380 kg/m^3, m=1.0 kg a stirring rod in syrup over the 800 second time period, what is the average torque applied by the stirring rod? and what is the rate of rotational mechanical work supplied to the fluid by the stirring rod when the rotational speed is 200rpm? do fast i will 5 upvotes.
69 Output from a process contains 0.02 defective unit. Defective units that go undetected into final assemblies cost $25 each to replac An inspection process, which would detect and remove all defectives, can be established to test these units. However, the inspector, who can test 22 units per hour, is paid $10 per hour, including fringe benefits. Should an inspection station be established to test all units? ume that the line will operate at the same rate (i.e., the current production rate) regardless of whether or not the inspection ration is added. a-1. Without the inspector, what is the current hourly cost of defects? Note: Round your answer to 2 decimal places. a-2. Should an inspection station be established to test all units based on costs alone? a-3. If the inspection operation is added, what would be the cost to inspect each unit? Note: Round your answer to 2 decimal places.

SEE MORE QUESTIONS

Recommended textbooks for you

Understanding Business

Management

ISBN:

9781259929434

Author:

William Nickels

Publisher:

McGraw-Hill Education

Management (14th Edition)

Management

ISBN:

9780134527604

Author:

Stephen P. Robbins, Mary A. Coulter

Publisher:

PEARSON

Spreadsheet Modeling & Decision Analysis: A Pract…

Management

ISBN:

9781305947412

Author:

Cliff Ragsdale

Publisher:

Cengage Learning

Understanding Business

Management

ISBN:

9781259929434

Author:

William Nickels

Publisher:

McGraw-Hill Education

Management (14th Edition)

Management

ISBN:

9780134527604

Author:

Stephen P. Robbins, Mary A. Coulter

Publisher:

PEARSON

Spreadsheet Modeling & Decision Analysis: A Pract…

Management

ISBN:

9781305947412

Author:

Cliff Ragsdale

Publisher:

Cengage Learning

Management Information Systems: Managing The Digi…

Management

ISBN:

9780135191798

Author:

Kenneth C. Laudon, Jane P. Laudon

Publisher:

PEARSON

Business Essentials (12th Edition) (What's New in…

Management

ISBN:

9780134728391

Author:

Ronald J. Ebert, Ricky W. Griffin

Publisher:

PEARSON

Fundamentals of Management (10th Edition)

Management

ISBN:

9780134237473

Author:

Stephen P. Robbins, Mary A. Coulter, David A. De Cenzo

Publisher:

PEARSON

SEE MORE TEXTBOOKS