Using the principles of Mohr circle, for the soil elements shown, determine the following.a.)Maximum principal stressb.) Minimum principal stressc.) Normal Stress on plane ABd.) Tangential stress on plane AB 2) Using the principles of, Mohrs cirole, for the soil elementsshown, deter mine the following.a) Mayimum principal stressb) Minimum principal stressC) Novmal Streas on plane ABd) Tangential Stress on plane ABB150kTa45°25KPA95°

Answered: Image /qna-images/answer/8556df23-4f01-4b49-8770-e851129ce5e1.jpg

Using the principles of Mohrs circle, for the soil elements shown, det er mine the following. a) Mayimum principal stress b) Minimum principal stress C) Novmal Streas on plame AB d) Tangential Stress on plane AB -150kPa 25kPa 25kfa 45° lookfo

Using the principles of Mohrs circle, for the soil elements shown, det er mine the following. a) Mayimum principal stress b) Minimum principal stress C) Novmal Streas on plame AB d) Tangential Stress on plane AB -150kPa 25kPa 25kfa 45° lookfo

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show complete solution, include necessary figures. The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension.A. Draw the Mohr's circle for this stress combination.B. What is the maximum shear stress acting at the point and what value of normal stress acts on the plane?C. Determine the value of the normal and shear stress acting on a plane that is 30 degrees from the minor principal plane.
If both the major and minor principal stresses for a soil element are known, as well as the strength parameters c'and o': A) Derive the formula that gives the orientation (the angle 0) of the theoretical failure plane. Hint: for the diagram below, assume 0₁ is acting in the vertical direction on the soil element (typical case) - i.e. the orientation of the failure plane with be measured on the Mohr's Circle from the Pole (which will be at 03). Remember a useful property of circles in terms of angles... Øs 03 01 B) Relate your answer from Part A to the failure plane assumed in Rankine's Active Earth Pressure. You can show this relationship with a simple sketch.
A soil profile is shown in figure below. Calculate the following:a. Effective stress at point A in kPa.b. Effective stress at point B in kPa.c. Effective stress at point C in kPa.
Stresses acting on an infinitesimal soil element are shown in the figure (with o₂ > 0). The major and minor principal stresses are o, and o3, respectively. Considering the compressive stresses as positive, which one of the following expressions correctly represents the angle between the major principal stress plane and the horizontal plane? ox ·0x
A sample of soil (0.1 m X 0.1 m) is subjected to the forces shown in Figure below. Determine (a) σ1, σ3, and α;(b) the maximum shear stress; and (c) the stresses on a plane oriented at 30° counterclockwise from the major principal stress plane.
N B 0 Horizontal The stresses shown in the figure are applied at a point in a dry clayey sand soil mass. A= 50 kPa and B= 125 kPa The shear strength parameters of the clayey sand are: c'= 9kPa and p'=29° 0=30° a) The value of the shear stress, T, is slowly increased. What value would cause shear failure at this point (in kPa)? b) At failure, what angle does the failure plane make with the horizontal (in degrees)?
The "total" shear strength parameters of a soil are given as: Cohesion, c 60 kPa; Angle of internal friction (also known as total friction angle).phi= 25 degrees If the normal shear stress (sigma) on a plane is 350 kPa calculate the total shear strength
A soil element is shown in Figure 2.32. Determine the following using Pole Method.a. Maximum and minimum principal stressesb. Normal and shear stresses on plane AB
A sample of sand is sheared in the following manner. First an all around normal stresso 350 kPa is applied to the sample. Next a shear stress is applied to the horizontal pia while the normal stress remains constant. The shear stresses at failure are + 186 kPa. Ihe initial stress and stress condition at failure are shown below 350 kPa 350 kPa 186 kPa 350 kPa 350 kPa ー550 kPa 550 kPa 186 kPa 350 kPa 350 kPa Initial Conditions At Failure Determine the Following: fo A) Assuming c, = 0, draw a failure envelope for the soil. Define the friction angle ( the soil. B) Draw the Mohr's Circle at failure for the test. C) Show the location of the pole. D) Define the maximum and minimum principal stresses at failure. E) Define the normal stress corresponding to the maximum shear stress
A soil profile consisting of three soil layers is shown. Assume: layer 1 as drysoil. Characteristics of the layers are: a=4 b=7 c=5 d=1 Determine:a.) The effective stress at Point Cb.) The maximum Neutral Stress at Point D
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and Sy = 215 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B = 50°. Sx
Limiting states 1. The MC describes the state of stress of our point in the field. That is, the MC shows us the values of the two principal stresses and the value of the maximum shear stress that the point is sustaining in the field. Consider a point in a geostatic soil mass. For our point, o'vo = 100 kPa and o'ho = 40 kPa. Take a sheet of paper and draw the Mohr Circle for this point carefully. 2. Now, we know that o'ho is a principal stress because t = 0 on the vertical plane (in the field). Similarly, o'vo is a principal stress because t = 0 on the horizontal plane (in the field). What is the value of t on the plane inclined 45 degrees clockwise from the horizontal? Go ahead and use your drawn MC to find this value. The value should be t = 30 kPa. 3. Note that the value found (t = 30 kPa) is the maximum shear stress that the point is supporting in the field, as it is under o'v = 100 kPa and o'h = 40 kPa. Consider now a situation in which o'h remains at 40 kPa, but o'y grows to 120…