Using the Pi-Buckingham method, prove that the entrance length (Le) relationship is Le F(Re) where Re is the Reynolds number! //MM Growing boundary layers Inviscid core flow u(r. x) Entrance length L (developing profile region) Boundary layers merge Developed velocity profile u(r) Fully developed flow region

Using the Pi-Buckingham method, prove that the entrance length (Le) relationship is Le F(Re) where Re is the Reynolds number! //MM Growing boundary layers Inviscid core flow u(r. x) Entrance length L (developing profile region) Boundary layers merge Developed velocity profile u(r) Fully developed flow region

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

solveeee very very fast in 15 min | I need a clear answer by hand, not by keyboard and thabk u | dybala
Q.4 A steady, uniform-density, 2-D flow is to be calculated on the square grid shown below. The boundary velocities are given as; v₁ =30, V = 40,uc=100, u = 50, u = 200, u, = 210, V = 0 and v₁ = 20. Among these numbers, there is some doubt about correctness of the value of u,. If all other numbers are correct, what should be the correct value of u,? The internal velocities are governed by simplified momentum equations given by: up = 70+0.5 (P₁-P₂) u, = 10 +0.7 (P3-P4) V =30+0.5(P3-P₁) VG =18+0.8(P₁-P₂) Write discretized continuity equation for each control volume. Derive the discretization equation for pressure by substituting from momentum equations, following SIMPLER calculation procedure. Solve the pressure equations to obtain P₁, P2, P3 and P₁. Hence obtain values of up, u, V and VG
Question 3 a) Neglecting freestream turbulence, the decelerating freestream velocity profile over a flat plate is given by, u = u₁ (1-x/L)", with L=10m. i) Estimate the point where the separation occurs, for n=1,2,3,4. ii) Consider the case when n=2 and estimate the momentum thickness at the separation point by the Walz-Thwaites's method. iii) Use Michel's method (after 1 iteration) to predict transition when u₁ = 10m/s and obtain an equation for the location of the transition point, x,,. State the assumption that was made to obtain the result. iv) Is x,, upstream or downstream of the point where separation occurs? b) If u is unknown, using Michel's formula for transition, find the value of u₁ = u₁_col that both separation and transition occur at the point of separation. (i.e. the two points are co-located.) such When, u > u₁_col, state whether the transition point x, is upstream (towards the leading edge) or downstream (towards the trailing edge) of the point where separation occurs?…
Subject: Fluid Dynamics Find the lift force of potential flow a half cylinder. please help me check my solution and verify the answer.
If the velocity varies linearty with distance through this fluid nozzie (vertical nozzle), where the specific gravity of the fluid is S-0.46, what will be the pressure gradient, halfway through the nozzle? Assume steady and inviscid flow 2 m/s 50 cm 6 mis Select one a. 38465.20 O b. -57697.80 O e. 19232.60 O d. 9616.30 e. 76930.40
I need the answer as soon as possible
Q.3 Air (density 1.2 kg/m3 and kinematic viscosity 15 centistokes) flows over a flat plate, at zero angle of incidence, at a velocity of 20 m/s. If Reynolds number at transition is taken as 2.5 × 105, maximum distance, from leading edge up to which the boundary layer remains laminar is
Solve it from 1 to 4 PLZ
Q4) Define the boundary layer, then find the thickness of boundary layer, shear stress, drag force and coefficiet of drag in terms of Re for the velocity profile of laminar boundary layer u/U=4(y/8)-6(y/8)5. Calcate the boundary layer thickness and drag force if the air flows over a sharp edged flat plate 1m long and 0.5m wide at a velocity 0.9m/s, the air density 1.23 kg/m³ and the kinematic viscosity is 1.46*10-5 m/s².
Question 11) Vortices are usually shed from the rear of a cylinder, which are placed in a uniform flow at low speeds. The vortices alternatively leave the top and the bottom of the cylinder, as shown in figure, causing an altemating force normal because of generating a dimensionless relationship for Kánmán vortex shedding frequency f (1/s) as a function of free-stream speed V(7m/s), fluid density p (kgm³), fluid viscosity µ (kg/m.s), sound velocity c (m/s), surface roughness & (m) and cylinder diameter D(m). || I-Determine the nondimensional a parameters using repeating variables, involving f, , c and u as nonrepeating variables ii-the dynamics of Bhosphorus bridge is investigated in a wind tunnel for the vortex generation behind the wires. A 1/59 scaled down model of the hanging wires is used in the laboratory. If vortex shedding frequency of of Bhosphorus bridge 590 Hz is measured in the laboratory at 29 m/s. Then detemine the expected frequency in the actual case exposed to 190 km/h…
The slip correction coefficient (C) for a particle with diameter 100 nm is: (assume: mean free path of air 2 = 0.066 um) (a) 1.0018 G2.8703 7. (b) 5.0174 (d) 1.0035 The terminal velocity (in cm/s) for a particle with diameter 10 um and Reynolds number Re 2.5x10: a6.7x10 (c) 1.7x103 8. (b) 3.3x10 (d) 3.3x105
i need the answer quickly