Using the method of joints, find the reaction forces at the supports and the force in each member of the truss. Indicate whether the member is in tension (T) or compression (C). B P=18.0 kN 15 m 9 m 13.5 m

Using the method of joints, find the reaction forces at the supports and the force in each member of the truss. Indicate whether the member is in tension (T) or compression (C). B P=18.0 kN 15 m 9 m 13.5 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Related questions

Q: Problem 1. For the truss shown below, determine the magnitude of force in each member and state if…

A: Note : in case of roller support, reaction acts normal to it

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given datatruss is givenon B point 5.6 KN load is givenon C point load 4.3 givenFindForce in member…

Q: 15 kN 4 3 B C 1.6 m A IF JE -1.2 m- -1.2 m- -1.2 m–> 18 kN

A: While using method of joints sign convention is very important so using + = Tensile member - =…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: QUESTION 1: [Method of Sections] For the simple truss in figure Q1 below, Figure QI: Simple tras…

A: Given:- To find: b To draw free Body Diagram; To find reactions at support…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Concept explainers

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.

Question

JESTION 5:
Using the method of joints, find the reaction forces at the supports and the force in each member of
the truss. Indicate whether the member is in tension (T) or compression (C).
P=18.0 kN
15 m
9 m
13.5 m
(Answer: AB=12.11 kN, AC=8.1 kN, CB=28.2 kN)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
For the beam shown: (a) determine the distance a for which the maximum positive and negative bending moments in the beam are equal; and (b) draw the corresponding shear and bending moment diagrams for the beam.
A 2.0 m wide strip foundation is placed in sand at 1.0 m depth. The properties of the sand are: = 19.5 kN/m3, c = 0 and =34. Determine the maximum wall load that the foundation can carry, with a factor of safety of 3.0, using a. Terzaghis original bearing capacity equation with his bearing capacity factors b. Meyerhofs modified bearing capacity equation with appropriate factors (Tables 16.2 and 16.3).
Determine the factor of safety against bottom heave for the braced cut described in Problem 15.18. Use Eqs. (15.66) and (15.70). For Eq. (15.70), assume the length of the cut, L = 18 m. 15.18 Refer to Figure 15.51 in which = 17.5 kN/m3, c = 60 kN/m2, and center-to-center spacing of struts is 5 m. Draw the earth pressure envelope and determine the strut loads at levels A, B, and C. FIG. 15.51
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
A braced cut shown in Figure P19.3 is to be made to a depth of 9.0 m in a saturated clay deposit where the unit weight is 17.65 kN/m3 and the undrained shear strength is 30 kN/m2. The struts are spaced horizontally at 3.0 m center to center. Find the strut loads.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
For the data given in this problem, determine the magnitude of the active thrust on the wall retaining a c soil, using the procedure discussed in Section 16.10. Given H = 15.0 ft, c = 100 lb/ft2, = 26, = 115 lb/ft3, kv = 0, and kh = 0.3.