Using the information below, use Excel and show the equation on how to solve for each:  #3: The data below was generated to assess the precision of an analytical balance using a NIST-certified 10.0000 g calibration mass.  Use it to compute the mean, standard deviation, upper and lower warning limits, and upper and lower action limits. Be sure to keep at least one guard digit in your calculations, and report the results to the correct number of significant figures.

Q: Find the standard deviation of the following data:

A: The frequency and size of items are given belowSize of items10111213141516Frequency2711151041`Need…

Q: Use the data provided to complete the MVR table and determine the engineering parameters listed…

A: Given:Gs = 2.75Water density= 62.3 lb/ft3water content= 13%Required:Volume of airVolume of…

Q: Consider the shaded area in (Figure 1). Suppose that a = 2 m, b = 2.5 m, and k = m-1 8 Figure a y =…

A: Given a parabolic segment in which the y coordinate of centroid is to be calculated. Consider an…

Q: a calibrated steel tape of 30m length supported at full length and under 6kg tensile strength and…

A: Lo (standard length of tape) = 30m dL = +0.02m(2cm) Lm (actual length of tape) = 30.02m To(standard…

Q: b) The following information has been collected in the lab during "Head Loss in Bends and Fittings"…

A: Part B answer Given data Manometer readings for sections before and after a bend: h1=326 mm and h 2=…

Q: An engineer collected a speed sample along a highway. The sample is shown as {30 mph, 35 mph, 44…

A: Given; The sample speed  (30 mph, 35 mph, 44 mph, 65 mph, 65 mph, 75 mph, 80 mph)

Q: What can you s

A: introduction: The degree of closeness to the true value is called accuracy. The degree of…

Q: Exercise 5.3 An electronic scale at an automated filling operation stops the manufacturing line…

A: Bu using the negative binomial distribution: Given: (a) The probability of success p is 0.01. The…

Q: is the total permissible variation in its size. Select one: O a. tolerance O b. dimension O c.…

A: Tolerance is the total permissible variation in the size of a dimension. Tolerance is the difference…

Q: 1. Using the tables below. Assume system failure if failure occurs < 0.5000. a. b. Calculate failure…

A: Failure Rate = (number of components)/( Sum of total failure time) = 10/(…

Q: Civil Engineering The snowmobile is traveling at 10 m/s when it leaves th embankment at A. Suppose…

A: Given v=10msθ=36°Range is R=vx×tR=vcos36·t

Q: . Using Excel create a graph (x-y scatterplot) showing the relationship between moisture content and…

A: Soil subdivision can be done in many ways and there are many types of soils such as clay, dust, etc.…

Q: A quantity was measured ten times with the following results: 34.630 m, 34.626 m, 34.634 m,34.628 m,…

A: To Determine: The most probable value, the probable error of the single measurement, the probable…

Q: slide before it stops. nificant figures and include the appro Units ?

A:

Q: c) Name the fitting from the lab experiment (excluding the valve) that should have the highest head…

A: In laboratory experiments involving fluid flow, the fittings used can have a significant impact on…

Q: I need help with the tables, how each value was calculated, please do it on excel and show what you…

A:

Q: Part A In case shown in (Figure 1), determine the z and y components of the resultant force. Suppose…

A: as per our guidelines, i can solve first 3 parts only (part A, part B and part C only)

Q: he simply supported beam shown, calculate the internal reactions at point C. 9 kip/ft A B |C 6 ft 18…

A:

Pressure and Stress