The force-elongation curve for a material is given below. The sample was a cylindrical rod with an initial diameter of 1 cm and a length of 10 cm. Determine the modulus, yield strength, tensile strength and % elongation for this material. 250 200 150 100 50 10 10.1 10.2 10.3 Length (cm) Force (kN)

The force-elongation curve for a material is given below. The sample was a cylindrical rod with an initial diameter of 1 cm and a length of 10 cm. Determine the modulus, yield strength, tensile strength and % elongation for this material. 250 200 150 100 50 10 10.1 10.2 10.3 Length (cm) Force (kN)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Consider a carefully conducted experiment in which an aluminum bar of 5.5cm of diameter is stressed…

Q: The stress-strain diagram of a structural material is given below. Find the following: (A) Elastic…

A: Given, Stress strain diagram To find : Elastic modulus, Johnson’s Apparent Elastic Limit, Yield…

Q: A solid plastic rod has a diameter of d = 19 mm and a length of L = 500 mm. An axial load of P= 24…

Q: minimum force required

Q: The representative curves of the applied stress versus the number of cycles for different metals are…

A: From the given graph it can be clearly seen that the fatigue strength of steel is greater than the…

Q: A material has the following properties: Sut = 400 MPa and n = 0.25. Calculate its strength…

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made…

Q: A tensile test was conducted on a specimen with a diameter of 0.5 in. A strain gage was bond pecimen…

A: The strain of the material is directly proportional to the value of stress within the elastic limit.…

Q: (a) A 20 mm diameter rod plastic is subjected to a tensile force of magnitude P = 6 kN. Knowing that…

Q: 8.13 A polycarbonate sample showed a craze growth length and time relation- ship of e=k log(t/to).…

A: Following is the given relationship between the craze growth length and time of the polycarbonate…

Q: The state of stresses in the xand y directions at a point in a given material is shown in the figure…

A: step 1-

Q: A solid plastic rod has a diameter of d = 18 mm and a length of L = 700 mm. An axial load of P = 33…

Q: 3. A thin strip of rubber has an initial length of 25 in. If it is stretched around a pipe having an…

A: Solution:Unstretched Length Lo= 25 inDiameter of pipe = 7 inTo find :Average Normal Strain…

Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…

A: Determine the angle of twist per meter length of the wing.

Q: A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

The force-elongation curve for a material is given below. The sample was a cylindrical rod with an initial
diameter of 1 cm and a length of 10 cm. Determine the modulus, yield strength, tensile strength and %
elongation for this material.
250
200
150
100
50
10
10.1
10.2
10.3
Length (cm)
Force (kN)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Calculate the Youngs modulus E

VIEW

Step 2 Find Yield strength and Tensile strength

VIEW

Step 3 Find Percentage elongation

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A student wants to measure the strain at a particular point K on a loaded specimen, so she affixes a 45° strain rosette at point K and obtains the following results: €A = 390 μrad EB = 275 μrad Ec = 325 prad After packing up and going home to analyse her results, she realises that the strain rosette was misaligned by 0 degrees CW (where a negative corresponds to CCW) from the x-y axes-ie. Gauge C is not parallel with the x-axis and is instead parallel with a different x' axis that is rotated by 0 degrees-where: 0 = 16 deg Instead of replacing the rosette and retaking measurements, the student realises she can use what she learned in ENGG2400 to find the strains she's interested in. b 45° 45° a) Draw a diagram of the situation, showing both the x-y axes and the strain rosette. b) Calculate Exx, Eyy and Yxy. c) Calculate the maximum in-plane shear strain and the associated average normal strain. I X
Osec σij = The hydrostatic stress for the state of stress represented by oij given below is MPa [100 50 50 125 75 75 75 = 50 50 1 MPa
The representative curves of the applied stress versus the number of cycles for different metals are shown in Figure Q2. Analyze both metals in terms of fatigue properties. 500 Stress amplitude (MN/m²) 400 300 200 100 0 1045 steel 10³ 104 2014-T6 aluminium 10⁹ 106 107 Number of cycles, N₂ Figure Q2: Representative curves of stress amplitude vs number of cycles 108 10⁹
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.50 in. to 1.60 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve Mandrel Answers: (a) ED = in./in. (b) Ес in./in.