Using the equation of best fit: A*(1-exp(-C*(t-t0)))+ B from the graph calculate the value of the time constant of the RL circuit.

Q: If you want a characteristic RL time constant of 1.00 s, and you have a 500 Ω resistor, what value…

A: Given: t =1 s R =500 ohm

Q: Chapter 30, Problem 050 The current in an RL circuit builds up to one-third of its steady-state…

A:

Q: Calculate the steady-state current the following LRC Series Circuit with the an of specifications:…

A: Lq''+Rq'+(1/c)×q=E(t)In question values given are :L=1(h)R= 2ΩC=0.25(f)E(t)=50cost V

Q: The phase angle in a certain RL circuit is 68° at a frequencyof 60.0 Hz. If R = 2.1 Ω for this…

A: Using the equation for phase angle in RL circuit, θ=tan-1XLRtanθ=XLRXL=R tanθ

Q: Consider the following RLC circuit with C = 500µF and L - 200 mH. The initial volatage across teh…

A:

Q: A Coiled telephone cord forms a spiral with 51-0 tumsa diameter of 1.30cm, and an unstretched length…

A: Given that For a spiral telephone cord the number of turns is N=51 diameter of the cord is d=1.3cm…

Q: Problem 2: The values for the components of the circuit shown in the figure are V= 12 V, C = 4.2 µF,…

A:

Q: Please don't provide handwritten solution...

A:

Q: (a) For the RL circuit, the equation was: dI E – L dt IR=0 Show by direct substitution that I(t) =…

A: For RL circuit the equation is, ε-LdIdt-IR=0 Substituting I(t)=εR1-e-RLt in left hand side,…

Q: An LRC circuit is set up with an inductance of 1/5 henry, a resistance of 1 ohm, and a capacitance…

A:

Q: 0- 0.5- 0.0- XE Auto Fit for: Latest | Potential Pot A (1-exp(-C'(t-10)))+B to: 6.72988 A: 1.283…

A: if we consider Y=B as our origin then the equation of fit line will become  A(1-e-C(t-to))…

Q: In a series RL circuit like (Figure 1), ε0 = 40 V, R = 3.0 Ω, and L = 2.4 H. If the current is 8.7…

A:

Q: The RLC circuit below is turned on att = 0 such that Vin 10t, for 0 < t < 6. %3D 30 2 2 H Vin + I…

A:

Q: The current in an RL circuit increases to 97% of its final value2 10 s after the switch is dosed.…

A:

Q: Suppose you need to construct a resonant frequency of 52.5 Hz. What inductance in henries do you…

A:

Q: Now that you un X atv Apple TV+ xM Inbox (410) - ralk x Bb Labs-2020SP_F X Bb EGR 1…

A: In the circuit 1, both the resistances are connected in series. Calculate the equivalent resistance…

Q: At an instant of time during the oscillations of an LC circuit.The current is at its maximum value…

A: Introduction: An LC circuit is an electric circuit consisting of an inductor,  and a capacitor…

Q: .Detarmine the time constant of the circuit. b) Sketch the wave for ms For vc and ic. 30uf t. 10/-

A: We need to calculate time constant of the circuit and plot graphs of Vc and Ic.

Q: An RLC circuit governed by the equation Lq" + Rq + q/C = E0(t)sin wt a)get the equation for the…

A:

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.