Using Partitioning Minimization Method, Reduce the state diagram shown in Fig.2 to a minimum number of states. Sketch the new state diagram after reduction 00, 11 01 00, 11 10 00 10 01 01 Fig. 10 00 01 10 01 10 00, 11 00, 11 10 10

A, B, C are the inputs, and D, E, F are the outputs. By “completely specified” it means that, for each current state, the next state for each possible input combination is specified.

b) Use the ALU 74181 in the figure below and the tables (one is enough; second maybe, need to check the new kit) to implement : A + B, A – B, A. B. (MSB) (LSB) 10 (MSB) F3 F2 F1 FO S3 Cn+4 16 s2 20 U14 15 S1 14 so A3 A2 A1 AO B3 B2 B1 B0 M Cn 24 23 22 21 28 27 T26 25 (LSB) (MSB) (LSB)(MSB) (LSB) And given that under M = 1 the circuit performs the following arithmetic and logic functions according to Table 11.1. Input selection S3 Output M-H S2 SI Cn=L. F3 F2 F1 FO A 1 -A В -B A&B AxB 1 A'B 1 Ax(-B) (-A)xB (-A)x(-B) 1 1 ACTIVE HIGH DATA M-L: ARITHMETIC OPERATIONS SELECTION M-H LOGIC s3 s2 s1 so Ino carry) (with carry) F-A PLUS 1 F- LA + B) PLUS 1 F- (A + BI PLUS 1 FUNCTIONS L L F-A F-A+B F-AB F-A H FA+B F-A+T F- MINUS 1 12s COMPL) F-A PLUS AB F- IA + BI PLUS AB L L L L F-0 F-ZERO F- AB F-A PLUS AB PLUS 1 F- (A + BI PLUS AB PLUS 1 L L L H L F-AOB F- AB L L F-A MINUS B MINUS 1 F-A MINUS B F- AB MINUS 1 F- A F-A PLUS AB PLUS1 F-A PLUS B PLUS 1 F- IA + B PLUS AB PLUS 1 L H L F-A PLUS AB…

can sameone solve this thanks

Detailed answer please

(02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value for RL needed to turn Zener diode ON?, And what is the maximum value for RL needed to turn Zener diode is ON? -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.

5. Your friend D. G. Tully is very excited because she figured out a way to transmit digital information wirelessly via a light signal. However, she does not know digital circuits so she comes to you for help. She shows you the circuit in figure 7. The circuit contains a Light dependent Resistor (LDR), which changes its resistance from Row when light is shone on it and Rhigh in the dark. VDD R₁ T for BRL (a) Configuration A Vo V DD J R₁ VDD Figure 7: LDR Receiver -L (b) Configuration B V₂ (a) Which circuit configuration will give you a non-inverting output i.e the output of the inverter, V, goes high when the light is bright and low when the light level is low and which one will give you the inverting output?

Help, please!

Design the circuit with the state diagram below with one-hot coding.

I need the correct expert solution with explanation of the steps of the solution and the abbreviations, please.