Use the Y-Y circuit shown below. What is the phase angle of the voltage drop of the line (wire) at phase c? Solve for the phase voltage VCN. Solve for the line current flowing through phase a.

Q: When we denote the direction of the line currents in a balance load, balance source system, it is…

A: Balanced electrical supply Voltage Magnitude of each phase remain same Line voltage displaced by…

Q: H.W. Calculate the per phase inductance and reactance of a balanced 36, 60 Hz, line with horizontal…

A: According to the question we have to find reactance and inductance per phase.

Q: Use Millman’s theorem and determine the magnitude of the neutral displacement voltage,(Vsn) in the…

A: The Given data is Za=0°18ΩZb=60°12ΩZc=60°30ΩEab=360VVsn=?

Q: What is the voltage drop in kV on the transmission line?

A:

Q: 6. Magnitude of line voltages is V3 times the magnitude of phase voltages V= V3 V,, what Phasor…

A: For star connection,  Line voltage = sqrt(3)×phase voltage.  Given VL =sqrt(3)×Vp. So we will draw…

Q: If T = 0.6260° and A = 20cm find the position of the second voltage maximum on the line. Select one:…

A: In this question we need to find a position of the second voltage maximum on the line

Q: Given the circuit below. a A 220°n U,07t 100 -V 3-ø source b U,097s ICA Igc 22-30°n Explain why the…

A:

Q: In a negative sequence, the current component of phase' c' ie. Ic2 can be expressed in terms of L2…

A: A negative sequence component is shown below,

Q: 4. In a balance 3-phase system, the load is wye-connected and one of the values given is 10230 2. If…

A:

Q: 1. Solve for the loop currents 1,12 & 13. (a) what are the loop current equations. (b) use Cramer's…

A: Please refer the attached images for the complete answer..

Q: Using an end short circuit parallel side line impedance matching circuit, impedance matching is…

A:

Q: Q. No. 01 [CLO1-C3]: Draw an impedance diagram for the electric power system shown in Figure-1,…

A: We can obtain the impedance diagram by using below steps: -  The base voltage VBG1  on the LV side…

Q: (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current…

A:

Q: Calculate the amplitude of the line voltage per phase at the load

A: This is 3 phase balance power circuit,  Calculate the amplitude of the line voltage per phase at the…

Q: Problem 9-AC phase shifts: The voltage and current waveforms shown below were measured across either…

A: The given waveform is shown below:

Q: Why do we need 220 V at 60 Hz in outlets? Why don’t we use DC in our transmission lines instead?

A: Transmission lines- Transmission lines are used to transfer electrical power from one place to…

Q: Explain the phase difference between line voltages and phase voltages in a positive sequence with…

A: In this question we will write about phase difference between line voltage and phase voltage in…

Q: Find the Q-points for the transistors shown and calculate the small-signalmodel parameters for the…

A:

Q: Current 450 Problems 9.8 A three phase Ihe be tween phase conductors of 4 m. Each con ductor has has…

A:

Q: Consider the three-phase system given in Figure Q1. The parameters of the system are: Generator…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Writo a matrox equation that determinos the loop currnts For each matrix, lot row 1 correspond to…

A:

Q: None

A: 1. Basics of Three-Phase Power:Definition: Three-phase power is a method of electrical power…

Q: Q-4: Obtain the line currents in the three-phase circuit shown in the following Figure with ZL =…

A:

Q: For the circuit shown above, what is the magnitude of the line c current? Assume that ZY = 9 + j 6…

A:

Q: DetermiNe z-Bus For the Network eee clee joz 12) joils 1, 13) Ś l:2 jisgら

A: The impedance circuit of the network is The Admittance circuit can be drawn by calculating…

Q: Given the circuit below. A 220'n U,07t 100 -v 3-4 source b B U,097$ ICA lạc 22- 30°n Determine the…

A: From the three phase system ..

Q: Describe equations for line transformation and phase transformation.

A:

Q: 3. A balanced current is flowing in a three-phase balanced line. If the self-inductance and mutual…

A: Given data:Self Inductance of line = Ls(mH)Mutual Inductance between lines = M (mH)Line current in…

Q: Design the series circuit needed to meet the voltage and current requirements as shown. Provide the…

A: a)

Q: 3. The equation P = E²/Z can be used to determine the power delivered to an AC circuit. Is this…

A: The objective is to determine if the statement is true or false.

Q: (b) Figure Q5(b) shows a 3.5 km long single phase distributor supplied two loads. The loads…

A:

Q: Using Gauss-Seidel method for the system shown in Figure 132 kV 1402 132/33 kV -50 MVA 10%…

A: Given system is 2 bus system Bus voltage at bus 1 = 132 kV  loads are L1 and L2, present at each…

Q: A 30, 50 Hz, 150 km line hay resistance inductive reactance., and Capacitive Shunt 2 and √3x10-6…

A: Total resistance per phase, ,Total reactance per phase, ,Capacitive susceptance, ,Receiving end…

Q: 9. If the equation of the phase A line current is -2.15 cos (wt-25°) amp flows through a balanced…

A:

Q: When we denote the direction of the line currents in a balance load, balance source system, t is…

A: Load is part of the electrical system which consumes the electrical power generated. The current is…

Q: Q3/A: The arrangement of a three-phase double circuit line is shown below. The self-GMD of…

A: Note Inductance (L) per phase in single phase or three phase system is given as   Lphase=2×10-7…

Q: Poor power factor causes greater voltage drop because the line voltage drop depends on the a. line…

A: power in circuit is p = voltage* current * power factor. voltage drop is current * line resistance

Q: What applications (uses) for 3-phase open Delta systems?

A: Open-delta systems : It is an emergency connection of a 3-phase delta connection. It is also known…

Q: The currents flowing in the lines toward a balanced load connected in delta are la = 100L0, lb =…

A: The solution is given below

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.