Use the data below from the titration of two water samples. Calculate the average ppm for the two trials. Volume of Water sample used for each titration 50.31 Concentration of EDTA used for both trails 0.012 Trial 1 Trial 2 Initial Syringe Volume - 8.98 Initial Syringe Volume - 9.46 Final Syringe Volume - 0.97 Final Syringe Volume - 1.53

Use the data below from the titration of two water samples. Calculate the average ppm for the two trials. Volume of Water sample used for each titration 50.31 Concentration of EDTA used for both trails 0.012 Trial 1 Trial 2 Initial Syringe Volume - 8.98 Initial Syringe Volume - 9.46 Final Syringe Volume - 0.97 Final Syringe Volume - 1.53

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter8: Sampling, Standardization, And Calibration

Section: Chapter Questions

Problem 8.1QAP

See similar textbooks

Related questions

Q: What is the Amax in nanometers that was determined for standard solution 1? Generation of the…

A: Given, λmax=429.8 nm

Q: Ten grams of hamburger (from a container of hamburger) were added to 90 mL of sterile buffer. This…

A: When a solute-solvent system is diluted by adding more solvent the amount of the solute in the…

Q: I need help calculating the Molarity of the solution in the first picture please!!!

A: In this question, we have to calculate Molarity in the first picture:

Q: PART ONE: Preparation of FECNS Solution Prepare the two solutions in table 1 by accurately measuring…

A: In part 1, when 1 ml of 0.0020 M CNS- solution is added to the unused portion of solution 1 in the…

Q: C. Preparation of Standard Curve and Beer's Law Analysis. Video for Part C Fill in the table below.…

A: A question based on Beer-Lambert law, which is to be accomplished.

Q: A water sample was analyzed for iron content using the iron-phenanthroline method. Using the set of…

Q: We leached 200 g of our soil with 500 mL of NH4CI. The collected solution contained: 320 mg L-1 Ca2+…

Q: 1. Standardization of Sodium Hydroxide Primary Standard used: Formula Mass of Primary Standard: %…

A: In the given question we have to do the standardization of NaOH and to calculate the required NaOH…

Q: The lead level in a sample of contaminated soil was determined using AAS. 2.0 g sample was dissolved…

A: Atomic Absorption Spectroscopy is a technique for rapid trace metal analysis. It is an easy, and…

Q: Given the following data Dissolved Oxygen Titration Data Trial 1 Preparation of titrant 0.4455 g…

Q: 45.0 mL of an unknown FeCl3 solution is diluted to a total volume of 230.0 mL. The diluted FeCl3…

A: Given details, The final volume of FeCl3 = 230.0 mL The initial volume of FeCl3 = 45.0 mL The molar…

Q: A river water sample (250 mL) is filtered and 0.032 g of solid is collected on the filter paper.…

A: The total solid in the river sample in ppm, is to be determined from the given data. Given:Volume of…

Q: Based on the results of your experiment, do you have hard or soft water? Does this match the data…

A: The question is based on the concept of hardness of water. hardness is present due to presence of…

Q: use analytical separation and analyses to outline analytical separation method protocols that can be…

A: It has become an important need to prevent water pollution by removing all contaminants. Water is…

Q: The learners repeat the titration three times. The three titrations are referred to as trials 1. 2…

A: Given three titration diagrams for Trial 1 , Trial 2 and Trial 3 We need to read the volume of acid…

Q: After determining the absorbance of several standards of known concentration, the trendline for a…

A: The equation for a straight line is given by y=mx+c where m is the slope and c is the y-intercept.…

Q: Initial volume of buret (mL) 1.90 Mass of KHP (g) 2.075 Observations color change Final volume of…

A: Given data,Mass of KHP=2.075gInitial volume=1.90mLFinal volume=34.78mL

Q: The concentration and absorbance data below were collected for compound X. A sample of compound X of…

Q: While cleaning you find out that you unfortunately only have run out of your usual cleaning…

A: A solution contains solute (or stock solution) and a diluent. Given solution is of 1/15 dilution.…

Concept explainers

Applications of Molecular Spectroscopy

When light sources pass through the diffraction grating then light splits into different wavelengths. The light source produces two types of patterns that are shown as destructive and non-destructive. The light source is in the form of quanta that is quantitation.

Question

Use the data below from the titration of two water samples. Calculate the average ppm for the two trials.

Volume of Water sample used for each titration 50.31

Concentration of EDTA used for both trails 0.012

Trial 1 Trial 2

Initial Syringe Volume - 8.98 Initial Syringe Volume - 9.46

Final Syringe Volume - 0.97 Final Syringe Volume - 1.53

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

Table 2: Absorbance Values of Standards and Unknowns. Sample Blank Standard Solution 1 Standard Solution 2 Standard Solution 3 Standard Solution 4 Standard Solution 5 Water Sample 1 Water Sample 2 Phosphate Concentration (in ppm) Y17 0 ppm 0.02 ppm 0.04 ppm 0.08 ppm 0.16 ppm 0.32 ppm Freeman Lake 0.001 0.325 0.292 0.413 0.315 0.039 0.054 0.049 Absorbance at 2= 690 nm Calculations: 1. Construct a phosphate standard curve in Excel by plotting concentration (in ppm) on your x-axis and Absorbance (unitless) on your y-axis for your known solutions. Label the axes on the graph and provide the curve with a title. Use a linear trendline to generate a best fit line to your data. Label the graph with the equation and the R" value. Insert your labeled graph in the space below. X
A sample of rainwater was collected from four separate locations across theMetroplex. Each sample was measured once by two separate methods for the presence ofsulfate. Determine whether the two methods are equivalent with respect to giving thesame answer for [SO42-].
1. Data & Results 4.0 mglmL Concentration of stock solution (include units): Table 1-Beer's Law Plot Data V Volume of standard solution dispensed (mL) M, Diluted concentration (include units) Sample Absorbance A 2.00 mL 0.084 4.00 mL 0.173 l6.00 mL 0.259 8.00 mL 0.340 E 10.00 mL 0.418 Equation of trendline from Beer's Law plot: whats the diluted concentration and equation of trendline from the beers law plot once created?
A water sample was analyzed for iron content using the iron-phenanthroline method. Using the set of data from Question 15 (as presented below), Reagent Blank Absorbance Absorbance (au) Reagent Blank Absorbance 0.003 Concentration of Stock Solution: 10 ppm Volume of Stock Solution (mL) Total Volume of Standard Solution (mL) 0.50 10.00 1.00 10.00 2.00 10.00 3.00 10.00 4.00 10.00 5.00 10.00 Volume of Trial Unknown Solution (mL) 1 5.00 2 5.00 3 5.00 find the true concentration of Fe2+ of the original sample. A) 5.12 ppm B) 2.56 ppm 2.52 ppm D) 5.05 ppm Concentration of Standard Solution (ppm) Total Volume of Unknown Solution (mL) 10.00 10.00 10.00 Absorbance (au) 0.012 0.132 0.267 0.349 0.428 0.560 Absorbance (au) 0.289 0.296 0.281
1. Straight lime softening A groundwater was analyzed and found to have the following composition (all concentrations are as CaCO): Estimate the lime dose (in mg 1.) required to soften the water. HCO 155mg/1 Ca 210 mg Mg-15mg/1 Alk.-260 ml Temp-10C 2. Excess lime softening A groundwater was analyzed and found to have the following composition (all concentrations are as CaCO)). Estimate the lime dose (in mg/L.) required to soften the water.. H:CO 155mg/1 Ca 180 mg/1 Mg-60mg/1 Alk. -260 mg/1 Temp-10C
Color BEFORE adding Color AFTER adding Intensity of color AFTER adding FeCl3 Test Tube # FeCl3 FeCl3 #1 (salicylic acid) clear lilac 100% #2 (commercial aspirin A) clear slightly pink 50% #3 (commercial aspirin B) clear lilac 95% #4 (aspirin from your clear pink 20% synthesis above) #5 (control) clear clear 0% Based on this data and the melting point of Aspirin, how pure is the synthesized product?
Students measured the concentration of HCl in a solution by titrating with different indicators to find the end point. (Use the table to find critical F values.) Mean HCl concentration (M) (+ standard deviation) Indicator Number of measurements 1. Bromothymol blue 0.09565 + 0.00170 28 2. Methyl red 0.08681 ± 0.00098 18 3. Bromocresol green 0.08641 + 0.00106 29 Is the difference between Indicators 1 and 2 significant at the 95% confidence level? O Yes O No Fenlculated clegrees of freedom Ecalculated Is the difference between indicators 2 and 3 significant at the 95% confidence level? O Yes O No Fealculated Spooled tcalculated
5. Which term is INCORRECTLY defined? a. linear range - the range over which the response of an analytical method is proportional to analyte concentration b. dynamic range concentration range over which there is a measurable response to analyte, though the response is not linear c. blank solution - a solution containing all reagents and solvents used in the analysis to which no analyte is deliberately added d. standard solutions - solutions for which the standard deviation is known - 6. True or False: Internal standards correct random error caused by run-to-run variation. a. True b. False
Please help, here are the choices
Calculate the concentration of unknown red dye solution solution is not =12.9,134,12.55,0.34
Please provide the correct answers based on the following attached data.
A water sample was analyzed for the total hardness through the reaction between the sample and EDTA. The data obtained from the experiment are presented below (MM CaCO3 = 100.0869 g/mol): Table 1. Standrdization of the EDTA solution mass of CaCO3 used 0.4567 g Initial burette reading 8.20 mL Final burette reading 15.65 mL Volume consumed 7.45 mL Table 2. Determination of Hardness of Water Volume of water sample 50.00 mL Initial burette reading 15.65 mL Final burette reading 24.85 mL Volume consumed 9.20 mL O 12,390 ppm O 990 ppm O 11,270 ppm O 10,290 ppm