Based on the picturei) the sensitivity of method.ii) the concentration of lead in the soil in mg/kg. The lead level in a sample of contaminated soil was determined using AAS. A2.0 g sample was dissolved in acid and then diluted to a total volume of 50.0mL. The absorbance of this solution, determined in a spectrometer at awavelength of 218 nm, was found to be 0.20. Several standard solutions weretested under the same conditions and a calibration curve shown below wasobtained.0.80.70.60.50.40.30.20.15.010.0concentration of Pb (mg L-1)absorbance

Atomic Absorption Spectroscopy is a technique for rapid trace metal analysis. It is an easy, and…

The lead level in a sample of contaminated soil was determined using AAS. 2.0 g sample was dissolved in acid and then diluted to a total volume of 50. L. The absorbance of this solution, determined in a spectrometer at wavelength of 218 nm, was found to be 0.20. Several standard solutions wer ested under the same conditions and a calibration curve shown below wa obtained.

The lead level in a sample of contaminated soil was determined using AAS. 2.0 g sample was dissolved in acid and then diluted to a total volume of 50. L. The absorbance of this solution, determined in a spectrometer at wavelength of 218 nm, was found to be 0.20. Several standard solutions wer ested under the same conditions and a calibration curve shown below wa obtained.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter2: Basic Statistical Analysis With Excel

Section: Chapter Questions

Problem 10P

See similar textbooks

Similar questions

A student prepared four standard solutions of (NH4)2Fe(SO4)2 and measured their absorbance at 505 nm. She created a calibration plot with the best-fit line of y = 9372 x + 0.0539. She measured the absorbance of her diluted unknown sample solution as (4.69x10^-1) nm. If she prepared her diluted sample solution by diluting 10.00 mL of the original solution to a total volume of 50.00 mL with deionized water, what is the concentration of Fe2+ in her original solution? Answer in units of M. Note: Your answer is assumed to be reduced to the highest power possible.
0.1040 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 20. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 3.109 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer. Do not try to include the "%" in your answer. e.g. if your final answer is 10.01%, only write 10.01 in the box.
6. Blue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A solution is prepared by diluting 2.79 mL of the blue dye stock solution to 25.00 mL. The measured absorbance for the prepared solution is listed in the data table. (a) What is the theoretical molar concentration? [Blue]theoretical x 10 |M (b) What is the experimental molar concentration? [Blue]experimental x 10 M (c) What is the percent error? Percent error (blue) = %
0.1120 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 25. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 2.982 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer.
The determination of iron in wines was carried out by atomic absorption spectrophotometry, using the standard addition method. To do this, 10 mL of wine were placed in five 50 mL volumetric flasks; then 0, 5, 10, 15 and 20 mL of a 10 ppm iron standard solution were added to each of them. Next, they were gauged with distilled water and the absorbance was measured, obtaining the values of 0.040, 0.062, 0.081, 0.102 and 0.125 respectively. Calculate the regression parameters and obtain the iron concentration in the wine, in µg / mL.
3. The lead in a swab sample, lead standards, together with a blank were made up in 5.00 mL volumetric flasks using 0.2 % HNO3. 20 μL aliquots of these solutions were injected into the spectrophotometer and the absorbance measured at 217 nm. The following results were obtained. lead / ppb Absorbance 0 0.0591 10.00 0.0858 50.00 0.1926 100.0 0.3260 150.0 0.4594 200.0 0.5929 Swab sample 0.3700 (a) Determine the amount of lead in the swab sample in μg.
Blue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A solution is prepared by diluting 2.81 mL of the blue dye stock solution to 25.00 mL. The measure absorbance for the prepared solution is listed in the data table. (a) What is the theoretical molar concentration? [Blue]theoretical | × 10 |M (b) What is the experimental molar concentration? [Bluelexperimental x 10 M (c) What is the percent error? Percent error (blue) =
As part of an investigation on Pb in biological ecosystems, some grasses that grew along the road and were exposed to emissions from motor gasoline were collected. 6.2501 g of grass were calcined to destroy all organic matter, the inorganic residue was properly treated and finally made up to 100 mL. An aliquot of 50 mL of this solution was read in an atomic absorption spectrophotometer registering an absorbance of 0.1250; then 0.10 mL of a standard solution of 55 µg of Pb / mL were added to the other 50 mL, with this fortified sample, another absorbance measurement was made, which was 0.1798. Calculate the µg of Pb / g of grass
1
A liquid sample was analyzed for Fe³+. A plot of absorbance (y-axis) vs. concentration (ppm; x-axis) of the external standards produced a calibration line with an equation y = 0.2256x -0.0903 (R² = 0.9973). The absorbance of the sample was 1.25. Determine the amount of Fe³+ in the sample (in ppm).
A solution in part C initially contains (4.06x10^-4) molar SCN¯ and (2.960x10^-3) molar Fe3+. This solution was then measured using the colorimeter, and an absorbance of (4.9800x10^-1) was recorded.The constant determined in part A of the experiment was found to be (3.8200x10^3). Using the data provided above, determine the equilibrium concentration of SCN", [SCN]E in this solution. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer units
Give a clear handwritten answer with explanation