(USCS units) A sine bar is used to determine the angle of a part feature. The length of the sine bar = 8.000 in. The rolls have a diameter of 1.000 in. All inspection is performed on a surface plate. In order for the sine bar to match the angle of the part, the following gage blocks must be stacked: 2.0000, 0.5000, 0.2500, and 0.0050. Determine the angle of the part feature.

(USCS units) A sine bar is used to determine the angle of a part feature. The length of the sine bar = 8.000 in. The rolls have a diameter of 1.000 in. All inspection is performed on a surface plate. In order for the sine bar to match the angle of the part, the following gage blocks must be stacked: 2.0000, 0.5000, 0.2500, and 0.0050. Determine the angle of the part feature.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A wear allowance of 5% of the total tolerance band is applied to the GO side of the gage. Determine the nominal sizes of the GO gage. Round your answer to the nearest tenth of a thousandth of a inch
6. On an engineering drawing a dimension is laid out as 1.760 + 0.005 A note on the drawing states that all dimensions are in inches. Give numerical values for (a) The nominal dimension (b) The upper limit (c) The tolerance (d) The bilateral tolerance
Tolerance Table All dimensions in inches 15.00 + 0.25 11.0 + 0.4 3.1 X.X +0.1 3.100 X.XX +0.05 Х.XXX +0.001 All units in cm All units in cm All units in inches Calculate the nominal, minimum, and maximum height (in cm) of the three-cube stack shown at right. The cubes are stacked atop each other with no gaps between them. Pay special attention to units, and note that 1 inch equals 2.54 cm. C Hints: ??? • For each cube, calculate the nominal, minimum, and maximum height using the nominal heights and tolerances provided in the three drawings. Ensure that the cubes' heights and tolerances are all in the same units before adding them in the next step. • Add the three nominal heights to find the nominal height of the stacked cubes. • Do the same for the three minimum heights and three maximum heights. • The tolerance table for cube C does not apply to the drawings for cubes A or B. Show all your work. 1. Nominal height = cm %3D 2. Minimum height = cm %3D 3. Maximum height cm
How solve do you this 3 part question.
What are the x, y values for the following prismatic part? R0.25 1.500 1.500 1.500 4.000 2.000 1.000 Y 1.000 2.00 X 6.000· 00.5 General tolerance 0.020 All dimensions in inches R0.500
I need help answering this quick review pertaining to the print provided.
A 150.00-mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size
M5.20 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole. Awear allowance of 3% of the total tolerance band is applied to the GO side of the gage. Determine the nominal sizes of the NO-GO gage. Round your answer to the nearest thousandth of a mm.
High precision in angular measurements can be made using a sine bar. For using a 300 mm sine bar to inspect an angle on a part. The angle has a dimension of 37 45’ and the sine bare rolls have a diameter of 40 mm. Determine: (a) The height of the gauge block stack (value accurate to four decimals). (b) The total number of gauges used including protector slips.
44
In order to measure the extension of perfection in the mesh, the method of skewness is used.
Using the numbers from question 2, I apply a +/-.01 tol to the A dim, I apply a +/-.005 tol to the 4.00 dim. The maximum and minimum clearances I can have between the two parts is .045/.015. True or False?