Question: Calculate the percent of sodiumhypochlorite in the original bleach bottle usingyour average result.Solution AAverage titration volume dispensed: 41.19mL(N22S2O3 5H20)Actual Mass of Na2S203 5H2O : 6.811gConcentration of Na2S2O3 5H2O solution:0.0549M NaOCI(aq)+ 2HCI (aq) →NaCI+ H20 (aq) + C2 (9)(aq)12 (aq)+ 2 1 (aq)→ 12 (aq) + 2 Cl (aq)-25,0;2-(aq)+ l2 (aq)→ SĄ06“2-(aq) + 21 (aq)

The question is based on quantitative analysis. we have to calculate percentage sodium hypochloride…

uestion: Calculate the percent of sodium ypochlorite in the original bleach bottle using pur average result. olution A verage titration volume dispensed: 41.19mL Na2S203 5H20) ctual Mass of Na2S2O3 5H20 : 6.811g oncentration of Na2S203 5H2O solution: 0549M

uestion: Calculate the percent of sodium ypochlorite in the original bleach bottle using pur average result. olution A verage titration volume dispensed: 41.19mL Na2S203 5H20) ctual Mass of Na2S2O3 5H20 : 6.811g oncentration of Na2S203 5H2O solution: 0549M

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 0.5264-g sample containing KBr is dissolved in 50 mL distilled water. Titrating with 0.04738 M AgNO3 requires 24.57 mL to reach the Mohr endpoint. A blank titration requires 0.75 mL to reach the same endpoint. Report the % (w/w) KBr (MM = 119.0) in the sample. 26.19% 51.02 % 12.76 % 25.51 %
does this lab abstract look ok that i did?
If 100 mL of pharmaceutical preparation contain 20 mL of a 50% w/v solution of benzalkonium chloride , what is the percent strength of that agent in the solution?
Salt (NaCl) in food is determined by a potentiometric titration with silver nitrate as titrant and precipitation of Chloride. The salt content of a cracker is determined by extracting 10.0g of cracker with 100.0ml of water, filtered, and a 25ml aliquot titrated with 0.02M AgNO3. It takes 17.25ml to reach the end point. Calculate the weight % salt in the cracker.
Molarity of the standard solution NaOH is 0.0994M
Concentration of EDTA solution is 1.006 mg CaCO3/mL 10mL of unknown diluted with 40mL of distilled water 5mL of buffer and 5 drops of indicator what is the mg, ppm, and molarity for both trials?? Unknown titration with EDTA Trial 1 Trial 2 Volume of titrated 10mL 10mL Final Buret volume 4.1 4.5 Initial Buret Volume 25 25 Volume of EDTA solution used 20.9 20.5 mg of CaCO3 in sample ppm CaCO3 in sample Molarity of Ca2+
26. If 100 mL of a solution for patient-controlled anesthesia contains 200 mg of mor- phine sulfate and 8 mg of droperidol, calculate the percentage strength of each of these ingredients in the solution. 27, Oxycodone hydrochloride oral concentrate solution contains 20 mg/mL. If a
Calculate amount of vitamin c in sample (mg) and concentration of vitamin c (mg/ml). Given: DCIP (0.1mg/ml water), Molar mass of DCIP= 268.1 g/mol Molar mass of ascorbic acid (vitamin c)= 176.12 g/mol
Concentration sodium thiosulfate solution used: 0.056 mol L-1 ACCURATE TITRATION VOLUME OF SODIUM THIOSULFATE SOLUTION USED Volume titration 1, (ml) Volume titration 2, (ml) Your Group 15.80 15.75 Group 1 16.05 15.70 Group 2 16.30 16.25 ANALYSIS Average volume used, (mL) Standard deviation Number of moles sodium thiosulfate used, (mol) Number of moles calcium iodate in solution, (mol) Volume of calcium iodate used, (mL) Concentration of saturated calcium iodate solution (mol L-¹) Unrounded value 15.9750 0.26220 Rounded value 15.97 0.262 10.0
Titration of KOH using HCI Standardization of HCI solution using Na2CO3 *MW of Na2CO3 = 106 g/mol *MW of HCI = 36.45 g/mol TRIAL 1 2 3 Titration Using a pipette, 20 mL aliquot was taken from the prepared solution to titrate with HCI. 1 IN Mass of sodium carbonate (g) 13.25 2 3 V Analyte (mL) 20 20 20 V Analyte (mL) VOLUME OF H₂O (mL) 250 30 30 30 Initial Reading of the Titrant (ML) 33.5 33.5 33.5 AVERAGE Initial Reading of the Titrant (mL) Calculate the initial concentration in terms of Molarity (M) for the KOH solution which is to be titrated using the standardized HCI solution. TRIAL 50 50 Final Reading of the Titrant (mL) 9.85 10.05 50 AVERAGE 9.96 MOLARITY (M) Na2CO3 Solution Final Reading of the Titrant (mL) 35.3 34.8 35.0 3 Volume of Titrant used (mL) 1 1 1 Volume of Titrant used (mL) 1 1 MOLARITY HCI (M) 1 4 4 4 2 MOLARITY KOH (M) 4 4 4 2
At equivalence ____ ml titration was delivered Ph of mid point is____ Analyte is _____ Best indicator is ___
39. Three more samples of KHP (GFW=204.23g/mole) weighing 0.8001g, 0.7001, and 0.7666g were titrated with the same sodium hydroxide solution. The volumes for the titrations were 21.55mL, 17.44, and 18.37mL respectively. A.) Calculate three more values for the molarity =, then B.) Calculate the mean for all four measurements. And calculate the average for all for measureme ement ave. mean.