Two wooden planks, each 1/2 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.20 ksi, determine the magnitude P of the axial load that will cause the joint to fail. -을 in. in. 1 in. 12 in. P' 2 in. I in. 9 in.

Two wooden planks, each 1/2 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.20 ksi, determine the magnitude P of the axial load that will cause the joint to fail. -을 in. in. 1 in. 12 in. P' 2 in. I in. 9 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the minimum dimension h to the nearest 1/8 in. of the beam’s cross section to safely support the load. The wood has an allowable normal stress of 2 ksi and an allowable shear stress of 200 psi
Hi can you please complete the question fully thanks so much
A wooden joist 15 cm deep by 7.5 cm wide is reinforced by gluing to its lower face a steel strip 7.5 cm wide by 0.3 cm thick. The joist is simply-supported over a span of 3 m and carries a uniformly distributed load of 5000 N. Find the maximum direct stresses in the wood and steel and the maximum shearing stress in the glue. Take Es/Et = 20. (Cambridge) Answer: wood 4.56 MN/m2; steel 52.9 MN/m2; glue 0.21 MN/m2. Show your solution
Determine the smallest permissible diameter of the pole. ____________ inches in 2 decimal places.
Solve the problem-CIvil Thanks
The assembly shown consists of two wooden members joined by metal plates. steel and four steel screws. The diameter of the screws is “d”. Determine: a) The crushing force between the wood and the screws. b) The shear stress in the wood.
A composite beam 225 mm wide x 300 mm deep x 4 m long is made by bolting two 100-mm- wide x 300-mm-deep timber planks to the sides of a 25 x 300-mm structural aluminium plate. The moduli of elasticity for the timber and aluminium are 8 GPa and 73 GPa, respectively. Determine the maximum tensile flexural stress in each of the materials if the composite beam is simply supported and carries a concentrated load 30 kN in the centre of the beam. 100 mm 25 mm 100 mm 11 300 mm
Determine the minimum dimension a to the nearest mm of the beam's cross section safely support the load.The wood has an allowable normal stress of 10 MPa and an allowable shear stress of 1 MPa.
A timber column, 8 in. × 8 in. in cross section, is reinforced on each side by a steel plate 8 in. wide and t in. thick. Determine the thickness t so that the column will support an axial load of 300 kips without exceeding a maximum timber stress of 1200 psi or a maximum steel stress of 20 ksi. The moduli of elasticity are 1.5 × 106 psi for timber, and 29 × 106 psi for steel.
A timber wall 75 mm wide, 75 mm deep and 3.50 m high is assumed to be fixed at the top and bottom. It is subjected to uniformly distributed load of 388 N/m acting along the weaker axis of its entire height. The wall is made up of Apitong wood with 80% stress grade with properties as shown: Bending and tension parallel to the grain = 16.5 MPa Modulus of Elasticity in Bending = 7310 MPa Compression parallel to the grain = 9.56 MPa Compression perpendicular to the grain = 2.20 MPa Compute for the following: a) Allowable compressive stress b) Allowable bending stress c) Maximum axial load %3D %3D %3D
The two pieces of wood, 2.94in. by 4.76 in., are glued together along the 48ᴼjoint. Determine the maximum safe axial load P (in lb) that can be applied if the shear stress in the glue is limited to 275 psi. Round off the final answer to three decimal places.
Determine the minimum dimension b to the nearest mm of the beam’s cross section to safely support the load. The wood has an allowable normal stress of 12 MPa and an allowable shear stress of 1.5 MPa