Stresses Problem 5: The rectangular wood panel is formed by gluing together two boards along the 30-degree seam as shown in the figure. Determine the largest axial force P that can be carried safely by the panel if the working stress for the wood is 1120 psi, and the normal and shear stresses in the glue are limited to 700 psi and 450 psi, respectively. 1.0 in.- 4 in.- 30 T.

Stresses Problem 5: The rectangular wood panel is formed by gluing together two boards along the 30-degree seam as shown in the figure. Determine the largest axial force P that can be carried safely by the panel if the working stress for the wood is 1120 psi, and the normal and shear stresses in the glue are limited to 700 psi and 450 psi, respectively. 1.0 in.- 4 in.- 30 T.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

y 1 k 2" -12"- 3" 10" 10" -x For the composite area shown below, Find the centroid of the composite area. Determine ly of the composite area about its y' centroidal axis found in part (a).
4
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Final answer must be 2 decimal places, dont round off initial values ty
please answer step by step
Concrete has no tensile strength. True False
Two wood boards, each 15 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 995 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 5.6 kN. Use a = 21 mm and b = 168 mm. d Glue b P P a Answer: d = i mm
Two wood boards, each 17 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 1045 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 6.2 kN. Use a = 26 mm and b = 208 mm. Glue b P P Answer: d= i mm
1 Situation 19. A composite beam shown is subjected to a bending moment of 500 kN-m. Determine the maximum flexural stress; 300 VIEW INNOVATIONS 200 200 100 55. Experienced by the steel 56. Experienced by the aluminum A. 0.03 B. 25.24 57. Experienced by the brass A. 25.24 B. 37.86 REVIEW I EW INNOVATIONS Steel, E=200 GPa Aluminum, E=70 GPa Brass, E-105 GPa wwwww C. 48.2 D. 72.11 C. 16.8 C. 16.8 D. 11.21 VIEW INNOVATIONS REVIEW INNOVATIONS REVIEW IS
Required information A composite beam is made by attaching the timber and steel portions shown with bolts of 12-mm diameter spaced longitudinally every 200 mm. The modulus of elasticity is 10 GPa for the wood and 200 GPa for the steel. The vertical shear is 4.4 kN. 12 mm 250 mm 12 mm 150 mm- Determine the average shearing stress in the bolts. (Round the final answers to two decimal places.) The average shearing stress in the bolts is MPa.
Question 4 A 6 KN force is applied at the free end of a wood (E = 12GPa) beam with dimensions given in Fig. Q4. Neglecting the effect of fillets and stress concentration, determine (a) the maximum compressive stress and its location at section A-A; (b) the maximum shearing stress and its location at section A-A; (c) the deflection at section A-A. 6 kN 300 mm 400 mm ΤΑ 叶 ¡A Fig. Q4 96 mm -- 12 mm 12 mm 48 mm
Two pieces of wood, 60 mm by 120 mm each are glued together along the 40° joint. The permissible normal stress in the glue is limited to 100 MPa. The maximum safe load that can be applied at the joint is P+ 40° 60 mm P