Two wooden members shown which support a 4.5kip load, are joined by plywood splices fully glued on the surfaces in contact. The ultimate shearing stress in the glue is 360psi and the clearance between members is 1/4in. Determine the required length L of each splice if a factor of safety of 2.75 is to be achieved. 4.5kips Bin 4.5kips Y4 in

Two wooden members shown which support a 4.5kip load, are joined by plywood splices fully glued on the surfaces in contact. The ultimate shearing stress in the glue is 360psi and the clearance between members is 1/4in. Determine the required length L of each splice if a factor of safety of 2.75 is to be achieved. 4.5kips Bin 4.5kips Y4 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic: Stresses in Beams Instructions: Find the value of: y = C = A' = y' = I =
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)s=150 MPa and (Gallow)b= 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w Aluminum 2w 10 mm Brass 10 mm Steel 20 mm 2m - 40 mm
choose the correct answer
Y 3" 3" Determine the location of the centroid of the composite figure shown.
Problem 2 14600ksi, apr For the shown structure, AB is made by C83400-red-brass (Ebr 9.8 × 10-6/ °F) and BC is made by 2014-T6-aluminum (Eal 10600ksi, a al = 12.8 × 10-6/°F). AB and BC are joined at the collar B and fixed connected at their ends. The cross sectional area of each member is 1.75 in². If there is no load in the = member when T₁ 50 °F. Now the temperature for both members are increased to T₂ = 120 °F. Determine (1) Reaction forces at fixed end C (2) The average normal stress in the member AB (3) The average normal stress in the member BC (4) Eventually, how far will the collar B be displaced? = = 3 ft 2 ft
Enter Delete Page End Down DETERMINE THE FORCES AT AL JOKTS 800 LB lo00 LB 13 15 4.5 2家 3.75 DETERMING THE AREA THE POSITION OF THE CENTROID ABOUT THE REFERENCE AXES AND THE MOMENT OF NERTIA ABOUT THE CENTROIDAL AXES OF THE COMPOSITE FI6URE
How to solve for the centroid of the composite body using the principle of moments and treat each part as a finite element of the whole figure (Show a step by step solution)
Prob. 4.6-6. As illustrated in Fig. P4.6-6, a composite shaft of length L is made by shrink-fitting a sleeve (element 1) over a solid core (element 2). A torsional load T, is applied to the shaft at end A, and end B is fixed against rotation. Let G₂ > G₁, and express your answers in terms of the shear- modulus ratio G₂/G₁. Determine expressions for the ratio of diameters (d/d): (a) if the torque T₁ is evenly divided between the sleeve and the core, and (b) if the maximum shear stress in the sleeve. (Tmax), is the same as the maximum shear stress in the core, (max)2- sleeve (1) core (2) P4.6-6, P4.6-7, P4.6-8, P4.6-9, P4.7-4, and P4.7-5
The beam shown has the following properties. f’c= 30 MPa, fc=13.5 MPa, fy=400 MPa, fs=200MPa. c) The cracked section properties Kd and ICR.
A simply supported beam, circular in cross section, of span L supports a point load W at mid span. The length of elastic-plastic zone at the plastic hinge will be A 0.33 L B 0.41 L C 0.50 L D 0.58 L
PLEASE ANSWER THIS QUESTION ASAP!!!
Dctcrminc the cxtcrnal forces acting on mcmber BG at points B, C, F and G of the composite structure shown below. 60 kN OF E 3 m od dgo o noleatm 1 m 1 m 4 m 1 m