The bending stress distribution for the given beam at the bottom fibre are of in nature. w kN/m A B O a. Zero O b. Compressive O c. Not defined d. Tensile

Q: Chapter 5, Problem 5/005 GO Tutorial Determine the x-coordinate of the centroid of the shaded area…

A:

Q: For 1.DU z The figure is made of a 4"radius half-circle inscribed in a 4" x 8"rectangle beside a 4"x…

A:

Q: What is the degree of freedom of the system shown? Choices: 1, 2, 3 or 4

A:

Q: Dry Flash Column Chromatography ? Please explain at your own words.

A: The process of separation of mixture is known as chromatography. Chromatography is a laboratory…

Q: Q:  (i) How to orient a hospital building so that it can get maximum natural light and ventilation.…

A: (1)- The building of hospital should be aligned in east direction as much as possible for maximum…

Q: Q5-) Explain the standard consistency Procedure? according to the guide manual No. 1042@2011.

A: The standard consistency of a cement paste is outlined as that consistency which is able to allow…

Q: 100 mm 150 mm

A:

Q: Identify the portion of a foot (12") as indicated by the reading from the zero mark (0) on the scale…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: PROBLEM 3. 20 mm 35 mm 20 mm The beam has a thin-walled cross section as shown and the wall…

A:

Q: *On the drawing attached, apply a runout requirement to make the left face perpendicular to the…

A: Introduction- Whenever the target is rotating once on the reference axis line, the run-out of the…

Q: This blueprint shows the layout for rectangular ducting for a home forced airheating system. The…

A: As per out rules and guidelines we solve only first three subparts kindly resubmit the remaining…

Q: * aut cad Ray is one of the commands for the drawing list. It is used to draw a ray, using two…

A: Explanation :  Ray  command in AutoCAD  is used to draw rays from a starting point in a perticular…

Q: Determine the polar moment of inertia with respect to the centroidal X and Y axes. Present detailed…

A: Given: Required: Polar moment of inertia about centroidal x and y axes

Q: My book says the right answer was 90 kPa

A: Given data in question  Unit weight of dry bark clay 18 kN/m3 Saturated unit weight 15 kN/m3 and 21…

Q: 1. For the following list, provide an appropriate definition along with the APA reference for each.…

A:

Q: Define fiber-optic piezometer.

A: A piezometer is a device which is used for measurement of pressure of a fluid in a system or at a…

Q: Using the following notes, what is the elevation of BM,4 Station B.S. F.S HI Elevation BM12 4.64…

A: what is the elevation of BM₁4

Q: 2. Explain the difference between the TRIM default option and TRIM double enter. O Enter your answer

A: Trim default: This tool is simple to use. We need to just select the object which needs to be…

Q: Write a short note on the software used for determining magnetic declination.

A: As we know, the earth has every complex shape of the earth magnetic field at the same place the…

Q: What is the level rod reading in feet at the main crosshair line shown in the figure? (enter only a…

A:

Q: Question #8 Determine the centerline length_(wall is 200 mm thick) 31500 8200 10250 19200 006E 000Z

A: NOTE : as per our guidelines we are supposed to answer only one question, kindly repost the another…

Q: What is the use of a magnetic needle?

A: Magnetic needle The magnetic needle is used in compasses that are magnetic in nature.

Q: Breaks the selected object .between two points You can create arc or line between two specified…

A: Given- Breaks the selected object .between two points   a) You can create arc or line between two…

Q: Calculate the y-coordinate of the centroid of the shaded area. 53 mm 22 mm 22 22 mm mm Answer: ỹ : i…

A:

Q: installed in the front lawn and along one side and seeded the remain- der with 3.5 pounds per 1,000…

A:

Q: 200N 30 R, "y at point C

A:

Q: Civil Engineering Department Answer Sheet Date: Time: P-400 30

A:

Q: A blueprint for the floor of a natural history museum is shown the scale of the museum to the…

A: Given- A blueprint for the floor of a natural history museum. scale used=20 yards to 1 inch…

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: P₁ 3 m E B P₂ 3 m- D 4 m

A: Given TrussLoadsTo find out Zero force members

Q: PROBLEM 3 Class Interval f 30-34 2 35-39 40-44 7 45-49 8. 50-54 10 55-59 7 60-64 6. 65-69 4 70 -74…

A:

Q: Using Nscp 2015 Hint answer 145mm,205mm,270mm,140mm

A: Based on the assumptions made, the numbers (145mm, 205mm, 270mm, 140mm) could represent various…

Q: What are servomotors?

A: Servomotors are used in cars to control its speed.

Q: 10 20 10 +¹0| -25 30 20, 70 Dimensions in millimeters x Break the shaded area into the five…

A:

Q: Write in detail about soil stabilization and its objectives.

A: Soil Stabilization : Soil stabilization is defined as a process of treating(physically r chemically)…

Q: Need clear and complete solutions. Determine the coordinates of the centroid of the shaded area. 10…

A: Given data

Q: Determine the centroid with respect to the indicated X and Y axes of the area shown. Present…

A: Given data in question  Dimensions 35 mm and 80 mm height Circle 15 mm radius Semi circle 35 mm…

Q: The uniform 8-ft board is pushed down into the water so it makes an angle of 30 degrees with the…

A:

Q: * Next Px ? |(-50.6867-37.59+ 103.368 2)× (.37+li65p t1.lk)

A:

Q: Opaque elements in the building envelope exclude: Select one: a. Windows and skylights b. Roof and…

A: Given data  Elements of building  Opaque material