Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB LCD-1.3 m, LBc-3.3 m, P=16 kN, b=180 mm, t-17 mm, tw-11 mm, d=167 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. Answers: maxT = maxC = LAB i i P B LBC by T Cross section MPa MPa LCD

Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB LCD-1.3 m, LBc-3.3 m, P=16 kN, b=180 mm, t-17 mm, tw-11 mm, d=167 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. Answers: maxT = maxC = LAB i i P B LBC by T Cross section MPa MPa LCD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Activity 3 Questions WHAT'S YOUR SCORE? Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5º. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm 500 mm
please recheck your final answer.
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
Pls solve it
Use 3 decimal places
Situation 2: The bar AB is being supported by bars at each end. The length and the area for each bar are given. Determine the distance x to where the 100 N load must be applied if the bars must have the same stress. A. Distance x (feet) L-3 ft A= 0.2 in L=2 ft A= 0.3 in 100 N B. 8 ft
Please show all steps so your process is easy to follow
Need answer fast.
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0